Indesit W93 prob.

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Indesit W93 prob.

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • November 16, 2005 at 4:55 am #13350
    spark
    Participant

    Prob. with Indesit W93
    Prog. knob keeps rotating quickly but no wash.

    Owner says this prob.affected only one programme when it first occured.

    Thanks in anticipation.

    Spark

    November 16, 2005 at 6:59 am #154366
    bobokines
    Participant

    Re: Indesit W93 prob.

    You need to count the number of flashes whilst the timer is advancing. This will indicate an error code.

    Look here for the answers

    http://www.ukwhitegoods.co.uk/modules.p … topic&t=40

    Bob

    November 16, 2005 at 9:05 am #154367
    leavemetogetonwithit
    Participant

    Re: Indesit W93 prob.

    You can get boards repaired/ exchanged at emwelec.co.uk or qer.biz
    And if the diagnosis is wrong you don’t pay so much.
    Mike.

    November 16, 2005 at 8:57 pm #154368
    Tony_EMW
    Participant

    Re: Indesit W93 prob.

    Before sending the board to us, have a look at :
    1 edge connectors – tighten each pin with a stanley blade
    2 damp ? these boards don’t care for damp or condensation – unplug
    the machine and dry the board with a hairdryer – tell the customer to ventilate the kitchen more
    3 uneven wear on carbon brushes – they may have 90{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} life left but if they wear slightly unevenly the dreaded timer will rotate
    4 open circuit components – heater/pump/thermister (2 on dryers) – they will all send the timer around
    5 motor – try another as a last resort
    Only after everything else exhausted send the board to us.
    I only mention this because about 40{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the boards sent in have no fault
    Tony http://www.emwelec.co.uk

    November 16, 2005 at 11:45 pm #154369
    leavemetogetonwithit
    Participant

    Re: Indesit W93 prob.

    Useful info. Probably should be at the top of the error codes thread?
    Mike.

    November 17, 2005 at 5:05 am #154370
    spark
    Participant

    Re: Indesit W93 prob.

    Thanks to all, will check all and let you know the result.

    Regards spark

    November 17, 2005 at 8:09 am #154371
    Phidom
    Participant

    Re: Indesit W93 prob.

    I don’t understand the bit about uneven wear on the brushes. I would have thought they were either making contact or not making contact. 😕

    November 18, 2005 at 5:07 pm #154372
    Phidom
    Participant

    Re: Indesit W93 prob.

    Tony_EMW wrote:Only after everything else exhausted send the board to us.
    I only mention this because about 40{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the boards sent in have no fault
    Tony http://www.emwelec.co.uk

    Does this mean that 40{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the time you only charge a test fee rather than a repair fee? I just paid £41 for a repair to a W143S UK module and the machine is as bad as ever. 😥

    November 18, 2005 at 7:39 pm #154373
    Tony_EMW
    Participant

    Re: Indesit W93 prob.

    Correct. 40{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the boards sent in are charged at £4+vat as test only. Your board had work done on it as a result of dampness jumping the tracks and was finally reprogrammed. Send your board back for a full credit of £41 and we will then re-test it and put it into our stock.
    Tony http://www.emwelec.co.uk

    November 18, 2005 at 9:34 pm #154374
    Phidom
    Participant

    Re: Indesit W93 prob.

    If the machine is scrapped I might take you up on that offer (customer permitting).

  • Author
    Posts
Viewing 10 posts - 1 through 10 (of 10 total)
  • You must be logged in to reply to this topic.