Zanussi Configuration codes

Home › Forums › General Trade Forum › Zanussi Configuration codes

Viewing 15 posts - 1 through 15 (of 16 total)
1 2
  • Author
    Posts
  • November 29, 2005 at 5:29 pm #13686
    Tubs
    Participant

    Hi all

    Anyone had any problems while configuring an EWM2000 module locking up half way though configuring it ❓

    Tried another module but still the same 😯

    Steve

    November 29, 2005 at 6:00 pm #156122
    Martin114
    Participant

    Re: Zanussi Configuration codes

    Hi Steve, I once had exactly this problem, and in the end it turns out to be a software problem when fitted to certain models and the only cure is to fit a pre-configured module. 👿

    November 29, 2005 at 9:33 pm #156123
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Thanks Martin

    Will try and source one from Electrolux, Anyone know who repairs these boards? Tried EMW but they cannot source components.

    Steve

    November 29, 2005 at 11:21 pm #156124
    Dave_Conway
    Participant

    Re: Zanussi Configuration codes

    Tubs wrote:Anyone know who repairs these boards?

    http://www.qer.biz/prodRepairs.asp 😉

    Type “EWM2000” in the search field, send off and repair service only though, no exchange 🙂

    Dave.

    December 1, 2005 at 1:57 pm #156125
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Thanks Dave

    Spoke to Electrolux today and they only sell non configured boards ❗

    Rang to speak to electrolux tech, but gave up after 30 mins of being on hold :eeek: (could have had a Bosch upside down and everything according to the other thread 😉 :rotfl: )

    Have lost TDS at moment ( usuall teething problems with new installation)

    Anyone know if new disc has any info on this problem. Have correct board according to Electrolux 🙄

    Steve

    December 1, 2005 at 2:04 pm #156126
    Martin
    Participant

    Re: Zanussi Configuration codes

    Tubs wrote:Have lost TDS at moment ( usuall teething problems with new installation)

    Have you got broadband Steve?…I could email the info right now???

    December 1, 2005 at 2:09 pm #156127
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Yes Martin

    have, will P.M you my e mail address

    Thanks Steve

    December 1, 2005 at 3:18 pm #156128
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Martin

    Zanussi FJD1666w, PNC 914513519/00

    Start to configure module then it just locks up, wont let you press any buttons at all. Last error code is obviously E93
    Steve. board no. 1321221937

    Steve

    December 1, 2005 at 3:23 pm #156129
    Martin
    Participant

    Re: Zanussi Configuration codes

    I guess this is the code you put in then? 8FBC107A859B0146

    December 1, 2005 at 4:30 pm #156130
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Oh yes :tup: . Well half of it 😆

    December 1, 2005 at 7:22 pm #156131
    Flyman
    Participant

    Re: Zanussi Configuration codes

    Tubs, did you go into the fault system before you took the old board out to see if it had a fault registered? If there is a fault on say the motor then the machine will not let you configure a new board. 😕 Many of the fault codes are hidden from the customer and will only show when you go into the test system.

    December 1, 2005 at 8:45 pm #156132
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Hi Flyman

    Machine had waste pump running all the time (this is normal in some fault conditions) and control leds like something out of close encounters of the third kind.

    Yes went into dignostics and had E 51 if i remember correctly (motor triac short circuit) anyway checked and replaced main motor and done the usual loom checks. Upon furher inspection found that the recirculating pump was just a melted blob, bugger to spot under that white cover at first glance (measured just 20 ohms) Looking at circuit ties in with Main motor triacs, possibly why I had E51 in the first place ❗


    So of course have E93 on new board (wrong config code)


    Thoughts please

    Steve

    December 1, 2005 at 9:05 pm #156133
    Flyman
    Participant

    Re: Zanussi Configuration codes

    Steve the code you have is definitely right and the part number is right so I still think you have another fault somewhere on the machine. Did you see any visible signs of damage to the old board? 😕

    December 1, 2005 at 9:24 pm #156134
    Tubs
    Participant

    Re: Zanussi Configuration codes

    Yer, was thinking the same thing, will have a look tomorrow if I get chance, thanks for your input

    Steve

    December 2, 2005 at 12:04 am #156135
    eastlmark
    Moderator

    Make sure you know your B from your 6 I had some probs with those when configuring one of these.

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 16 total)
1 2
  • You must be logged in to reply to this topic.