Diplomat ADP8322 problem

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › Diplomat ADP8322 problem

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • February 6, 2006 at 7:45 pm #15440
    AaronAaron
    Participant

    Hi hopefully someone can help me, my dishwasher has stopped washing properly. The tablet clearner thing remains untouched and cups and plates are still filthy after the cycle has finiashed.

    From what I’ve read on here it’s actually a Whirlpool machine….

    I’ve spoken to a few repairman in my area and they’ve all said it’s probably the pump. They’ve also told me that it’ll probably be cheaper to replace the machine.

    Can anyone verify that it’s probably the pump?? If so, where would be the best place to go a replacement??

    Many thanks.

    Aaron

    Would this be the item in question??

    February 6, 2006 at 9:14 pm #163613
    Penguin45
    Participant

    Re: Diplomat ADP8322 problem

    Ooh! The big Askoll pump – they don’t use that anymore. Stick up the 12 nc number on the label on the side of the door and we should be able to track it down as a Whirlpol part (cheaper).

    Regards,
    Penguin45.

    February 6, 2006 at 10:03 pm #163614
    Dave_Conway
    Participant

    Re: Diplomat ADP8322 problem

    Part number 481236158334 at £91.44 plus carriage.

    An email to spares@ukwhitegoods please if required 🙂

    Dave.

    February 8, 2006 at 9:44 am #163615
    AaronAaron
    Participant

    Re: Diplomat ADP8322 problem

    So do we think that it is the pump at fault then??

    Many thanks

    Aaron

    February 8, 2006 at 10:54 am #163616
    Dave_Conway
    Participant

    Re: Diplomat ADP8322 problem

    More than likely Aaron but we can’t be 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure 😉

    If you need a definite diagnosis, check the repairs@ link below 🙂

    Dave.

    April 10, 2006 at 2:44 pm #163617
    AaronAaron
    Participant

    Re: Diplomat ADP8322 problem

    I ordered the pump with the part no posted above, but it’s completley different. Was it the wrong part number??

    Cheers

    Aaron

    April 10, 2006 at 3:10 pm #163618
    Dave_Conway
    Participant

    Re: Diplomat ADP8322 problem

    Nope, the new pump will be a “real” motor not the magnetic type as the original but it fits in exactly the same way.

    There’s a small bag in the box with a couple of screws to secure the bracket on the new pump to the rear of the cabinet 🙂

    Dave.

    April 10, 2006 at 3:42 pm #163619
    AaronAaron
    Participant

    Re: Diplomat ADP8322 problem

    There wasn’t a bag with screws in it mate, but I can find a few screws, that’s not a problem.

    The pumps inlet and oulet are in different places and different sizes, so it’s not going to directly fit. Also the plug connections are different, so they’re not going to fit either.

    Any ideas??

    April 10, 2006 at 3:56 pm #163620
    Dave_Conway
    Participant

    Re: Diplomat ADP8322 problem

    Eek :eeek:

    I’ve just found your order, you ordered a Diplomat washing machine drain pump from the online shop, not the dishwasher circulation motor above (which isn’t in the shop).

    That may be partly my fault now I’ve read the email again from earlier, I bet you thought you were getting a bargain eh ? 😆

    I’ll email further info shortly to get it sorted.

    Dave.

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.