Whirlpool ADG994 won’t heat and has a stammer

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › Whirlpool ADG994 won’t heat and has a stammer

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • January 22, 2007 at 3:16 pm #24372
    jomutimer
    Participant

    Hi,

    My Whirlpool has gone through two stages of failure.

    The first one was that it would do the wash but it would not heat. At the same time as this fault there was another one. The cycle would end, but not quite. You would have to press the button again to get it to finish. After you pressed the button it went on for about 2 minutes and then was ready for the next load. Amazingly it would clean pretty well like this. But now a new fault has developed. If you hit the button it makes a sound like it is trying to fill, but can’t, and then, after perhaps 2 minutes, it gives up.

    Throughout both of these problems the dishwasher consumed no salt.

    Before all of this the dishjwasher had been abused pretty badly by not giving it any salt! I thought it was getting softwater from our water softener, but it wasn’t (groan).

    Regards

    Adrian

    January 22, 2007 at 5:14 pm #201819
    Fairdeal
    Participant

    Re: Whirlpool ADG994 won’t heat and has a stammer

    Hi Adrian,

    Normally with the whirlpool dishwashers if it does not heat then it will stop during the cycle and the programme lights should flash.Does any light flash?

    Also if you can give the 85…. number ?

    Regards

    January 23, 2007 at 12:51 am #201820
    Penguin45
    Participant

    Re: Whirlpool ADG994 won’t heat and has a stammer

    Holding down the button “at the end of the cycle” will cancel the programme………. Count the flashes, before you cancel it.

    Regards,
    Penguin45.

    January 23, 2007 at 11:26 am #201821
    jomutimer
    Participant

    Re: Whirlpool ADG994 won’t heat and has a stammer

    Fairdeal wrote:Hi Adrian,

    Normally with the whirlpool dishwashers if it does not heat then it will stop during the cycle and the programme lights should flash.Does any light flash?

    [Adrian – Yes, thanks for reminding me of this. It does get stuck and the lights do flash. If I press the button for four seconds it starts again, but the problem persists.]

    Also if you can give the 85…. number ?

    [Adrian – I would love to. Where is it to be found?]

    Regards

    January 25, 2007 at 1:24 pm #201822
    jomutimer
    Participant

    Re: Whirlpool ADG994 won’t heat – more help please

    Hi, I am not sure what to do next?

    Regards


    Adrian

    January 30, 2007 at 12:04 pm #201823
    jomutimer
    Participant

    Re: Whirlpool ADG994 won’t heat and has a stammer

    The flashing light just keeps flashing. It doesn’t stop so there is no particular number of flashes.

    Regards

    Adrian

    January 30, 2007 at 8:34 pm #201824
    DentedPorsche
    Participant

    Re: Whirlpool ADG994 won’t heat and has a stammer

    Continuous flashing indicates a fault with the NTC. Click on shop@, I’m sure you’ll find it in there.

    DP

  • Author
    Posts
Viewing 7 posts - 1 through 7 (of 7 total)
  • You must be logged in to reply to this topic.