Hotpoint CTD40

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Hotpoint CTD40

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • May 21, 2007 at 4:24 pm #27508
    Alanj
    Participant

    Hi Guys,
    Called to this machine today and found following lights flashing:- Time delay, pre creasecare and alarm along with rapid on/off light. Can’t figure error code from info on known error codes. Can anyone help please?

    Alan

    May 21, 2007 at 4:30 pm #214393
    iadom
    Moderator

    Re: Hotpoint CTD40

    The error codes are there, you just need to do a little maths by adding the values of the flashing lights together from the relevant post in the known error codes thread and comparing the result with the list for the CTD 85 etc.

    Can you give the lights by number from top rather than by name. If not it means I am going to have to dig out my manuals and try and identify the neons. 😥

    Jim.

    May 21, 2007 at 4:42 pm #214394
    iadom
    Moderator

    Re: Hotpoint CTD40

    Right, the picture in the manual is very faint but here goes.

    Time Delay vertical neon 1 has a value of 8
    Pre Creasecare…………..2 has a value of 4
    Alarm……………………….4 has a value of 1

    Giving a total of 13 ergo F13 Rear NTC open/short circuit.

    Jim.

    PS. Two different rear stat/ntv kits, need serial number/date code to ID.

    May 21, 2007 at 4:49 pm #214395
    Alanj
    Participant

    Re: Hotpoint CTD40

    Thanks iadom for the quick reply.The thing that threw me was the error codes said Pre creasecare was top light=16. making my error code 26.

    Thanks again
    Alan

    May 21, 2007 at 4:56 pm #214396
    Alanj
    Participant

    Re: Hotpoint CTD40

    Jim,

    do you know the part number for the ntc or is it part of a kit. There are three stats/cut outs on heater plate.

    Alan

    May 21, 2007 at 5:29 pm #214397
    iadom
    Moderator

    Re: Hotpoint CTD40

    Alanj wrote:Thanks iadom for the quick reply.The thing that threw me was the error codes said Pre creasecare was top light=16. making my error code 26.

    Thanks again
    Alan

    You need to read the post carefully and you will see it says one horizontal neon, POST CARE has a value of 16 and the top four vertical neons give the other values. 😉

    You will need the serial number or better still the 5 digit commercial code to ID the correct kit, two different ones, also I went to one on Saturday that only has a single stat & ntc at the back.

    Jim.

    May 21, 2007 at 5:50 pm #214398
    Alanj
    Participant

    Re: Hotpoint CTD40

    Jim,
    didn’t take the serial no. but machine has three round stats one in middle has solid case ie. no bi metalic discs.

    Alan

    May 21, 2007 at 6:10 pm #214399
    DentedPorsche
    Participant

    Re: Hotpoint CTD40

    One in the middle is an NTC, had one a few weeks back. 🙁

    Brian

    May 21, 2007 at 7:26 pm #214400
    iadom
    Moderator

    Re: Hotpoint CTD40

    You need the serial number, the kits are not interchangeable. 😥
    Individual stats/ntc not listed.

    Was the one in the middle black or white?

    If white you need a 1703607, if black you need 1703608.

    Jim.

    May 21, 2007 at 8:56 pm #214401
    Alanj
    Participant

    Re: Hotpoint CTD40

    Hi Jim,

    it was white, thanks.

    Alan

    August 24, 2007 at 10:54 pm #214402
    cornwell40
    Participant

    Re: Hotpoint CTD40

    Went to one today with what I thought was the normal white spot stat kit and came a cropper fitting it. Question is, do they both need to be changed like the older type?
    If there is a two piece (white spot cut out and NTC) kit anyone know the part number?

    TC

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.