Bosch – Neff – Siemens Fault Codes
|
![]() |
![]() |
There are a number of different versions of the electronics used in Bosch Group made washing machines and washer dryers that are sold as Bosch, Siemens and Neff and most of them use different fault or error codes when they have a problem or a spare part fails.
The error codes in this article pertain to integrated washer dryers from all three (Bosch, Neff and Siemens) as they are built on the same platform and should have model numbers that start with WVTi, WDi and V534. The error codes here may relate to other models niot listed but we cannot say this for certain as we have limited information as Bosch does not allow independent repairers access to technical support.
Before you start any investigation of the fault or even remove the lid of your Bosch washing machine or washer dryer, please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!
Please remember to support our site by buying Bosch washer dryer spares from our spare part store and, if you decide that you really need an engineer, please support the local repairers that help make this site possible, you can search for a Bosch washer dryer engineer using the engineer search.
Reset The Washing Machine
For most BSH-produced washing machines, the reset procedure appears to be much the same and is carried out by following the steps as follows in order:
- Turn the program dial to the off or reset position (should be at the 12 o’clock position)
- Turn the dial to the 6 o’clock position
- Press and hold down on the spin button and simultaneously turn the dial to the 7 o’clock position.
- Hold the spin button for around 5 seconds and then release.
- Turn the dial to the off position
Once the machine is powered up again the error should be reset or cleared.
If the same code comes up once again then there will be a problem of some kind that will require further investigation, diagnosis and any fault resolved. If you require further assistance to diagnose a problem with your washing machine please use the forums for that.
Bosch Washer Dryer Fault Codes
These fault codes are written for washing machine repairers and not for the general public by Bosch and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine, please refer to our washing machine fault finding guide from this link before you begin.
If you struggle or cannot find the appropriate fault code that you need for your washing machine please ask in the forums and the gusy there will do what they can to help and locate the meaning of the fault code you need
Please check that any Bosch washing machine spares recommended are suitable for use on your particular model and ENR code. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine. Please, don’t guess or assume as spares can be altered on a production run with the same model number, having several different alternative components used.
|
E01 |
Antiflood device in base has been activated
|
|
E04 |
Washer dryer wash NTC (temperature sensor) shorted or open circuit
|
|
E05 |
Water inlet valve error detected
|
|
E06 |
Drain error detected
|
|
E10 |
Motor fault detected
|
|
E14 |
Dryer NTC detected open or shorted
|
More Bosch/Neff/Siemens Washing Machine Help
Should you need more help and guidance, please use the links from this article as most of them will help you to understand your Bosch washing machine or washer dryer a lot better and probably very much help you in diagnosing the fault you have. Of course, there are many other articles on the site that will also help you do this.
In addition, you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
- We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
- We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
- We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
- No warranty is inferred, implied or given.
You also have to know that fault or error codes are not a “magic bullet”, they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old-fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this newfound knowledge, you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.
Please also note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Bosch washing machine model please post a request to confirm this in the forums.



We are a commercial,laundry and catering engineering company based in South Wales.We changed a bearing kit on siemens wm14s383gb after we changed and reset blushed power machine comes up with error code f34. Is this the door lock fault as it here is no motor action and not filling but you can hear relays clicking on power boardRegardsRoy JonesRJES ltd
F16 and F18 error code flashing on display for Bosch Exxcel washer/dryer 2009