bendix dishwasher

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › bendix dishwasher

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • January 8, 2008 at 12:15 am #33490
    fasetester
    Participant

    hi guys happy new year to one and all. i have to look at a bendix dishwasher it is not brining in any water. are the sump pipes easy to get at possible blockage i dont have the model number. the only thing i can tel you i had to remove the washer pump before. it sits in at the back. and pushes into the sump. and is held in by a metal bracket what pipes should i check is there a acco stop on these can you get at the pipes from the front on these dishwashers. thanks fasetester 🙂

    January 8, 2008 at 12:49 am #238893
    Penguin45
    Participant

    Re: bendix dishwasher

    Fase…………… If you’ve been to it before, why haven’t you got the model number? If the customer can’t tell MrsP on the phone, the very first thing I do is log the model and serial number, before I start work – then it goes on the computer and I’ve got it for ever.

    Push-in motor with a metal clip is an old Zanussi based machine, therefore it’ll be a blue tubes machine; have a read of this:
    http://www.ukwhitegoods.co.uk/modules.p … ge&pid=104

    Hope that helps,
    Chris.

    January 8, 2008 at 1:21 am #238894
    aqualectric
    Participant

    Re: bendix dishwasher

    Motor that pushes in from the back and held in by a metal bracket…… that’ll be the newer type with the IWMS metering unit behind the left side body panel.
    Short answer – if it’s blocked – change it. A clean out job is at best a temporary fix. Not worth the time in the long run. 😉

    HTH,

    Steve.

    January 8, 2008 at 3:49 pm #238895
    fasetester
    Participant

    Re: bendix dishwasher

    thanks guys for the replyies went to repair the dishwasher today. it was air locked turned off the water and removed the fill hose. what causes the air lock it is a tricity bendix eco save model DH102 type 911N81-2F how do you remove the kick plate on this dishwasher. what is the screw like thing with numbers in the front left hand corner for plus the sponge in the far left . thanks fasetester.

    January 8, 2008 at 6:09 pm #238896
    Penguin45
    Participant

    Re: bendix dishwasher

    It won’t be airlocked, Fase. The pneumatic safety shut off will have been operated due to the water matrix (IWMS) becoming choked. Have sent you a large file which will explain everything.

    Chris.

    January 9, 2008 at 1:58 pm #238897
    fasetester
    Participant

    Re: bendix dishwasher

    thanks chris where did you send the file to fasetester. 🙂

    January 9, 2008 at 2:39 pm #238898
    Martin
    Participant

    Re: bendix dishwasher

    fasetester wrote:thanks chris where did you send the file to fasetester. 🙂

    Your published email address fase if I’m any judge? Check your ‘in box’ I would? 8)

    January 10, 2008 at 2:30 pm #238899
    fasetester
    Participant

    Re: bendix dishwasher

    thanks guys for the information if the dishwasher stops filling again only cure is a new (IWMS) thanks fasetester.

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.