- This topic has 22 replies, 13 voices, and was last updated 17 years, 4 months ago by
.
-
Posts
-
hi guys had to repair a servis washing machine. model m6002w when switched on and put on any program nothing you can here a click coming from the board.
when switched on should the door interlock not lock. the door what is the connections on the interlock 1 black 3brown and then 2 gray. which is the feed and return and netural the black and brown is on a double connection the machine is only 2 yrs old. thanks fasetester 🙂
Re: servis machine
Hi
Check resistor “R1 ” along opposite side to the connector blocks , near the edge of the can . These go open its 42ohm 2watt.
When this resistor blows machine is dead.
MikeRe: servis machine
thanks washman where is the resistor. would that leave the door lock not locking which wire is the live and return on the door lock what kind of reistance reading should i get throught the interlock thanks fasetester.
Re: servis machine
any more info on which wire is live and return. is the gray one the Netural on the interlock. i put my meter across and not getting any reading when i used the volt stick it is lighting which means i have power to at least one wire. thanks fasetester 🙂
Re: servis machine
Hi
If that resistor goes open nothing will work not even the door lock.Machine will be completely dead.
Mike
Re: servis machine
fasetester wrote:thanks washman where is the resistor.
Washman refers to the resistor on the main module board fase. 😉
Re: servis machine
thanks guys for the reply. when switched on the power light comes on . and when you set the timer to any of the programs and press the start button one of the lights light the one with the tub symbol. but will not start the program. at that point should the door not be locked. does any one know which wire is which on the interlock .
when you put the dial back to 0 to reset and switch off and then switch on again. you can here a click coming from the board i read if the board is faulty even replacing it can run you into trouble other than a dry joint.
could the programmer be faulty ie dial. is there any way to test it does the interlock run through the pcb. or throught the program dial sorry for all the questions 😳 as i have to go back tomorrow its a one parent family and would like to sort it . fasetester
Re: servis machine
Hi
Interlock is through the PCB so it could be faulty PCB, also make sure that none of the buttons is stuck in as this can stop machine from programming.
Mike
Re: servis machine
I have had a few like this take the front pcb off and one of the buttons will be stuck in no option lights should come on unless you select them if it wont turn off then it will be stuck in causing the machine not to start.
Re: servis machine
thanks guys for all the help is their any way to test the program dial. and does any one know which wire is which on interlock. L in L out N is their a heater on the interlock like the hotpoint. and if i find damage on the pcb what would hav caused it and what should i check.
i checked the brushes on the motor. the are hard to get the spring back in does the holder on the motor come out. or do you push the brush and spring back in thanks fasetester.
Re: servis machine
Fase,
forget about the door lock at the mo!
do as suggested, take off the front board and check the switches arent sticking or breaking off the board.
the brushes go back in just as you would the bosch maxx range!
whilst your there get the part number off the main board, it will be on the label. 546089200 or something like that.
If it was R1 resistor at fault there would be no lights on at all. so forget that at the mo!
breathe!
Re: servis machine
hi guys went back to the machine took of front panel. removed board with the buttons checked nothing sticking. checked board could see nothing unusal. put back togeather again tested. now have 2 light flashing from left to right first light and last light but still no go.
switched power back off. removed board and checked for burning dry joints ect. could see nothing unusal niped up connections put back in retested same as before. number on board is 546089203 fasetester
Re: servis machine
it will be the board (it always is)
cheapest i have seen it is £60+vat
so £100 job minimum 😥
one parent family so no money (no offense meant)
they will already have had the catalogue out and decided to buy a new one for £5.25 a week
i would try and sell her a recon so at least you know she will have a good machine 😉
- You must be logged in to reply to this topic.