Configuring Zanussi module

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Configuring Zanussi module

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • February 26, 2009 at 9:19 am #43767
    pmb
    Participant

    Hi i have a module to replace on a zanussi iz16 and i have realised i don’t know how to configure it gulp 😳 can anyone please help me with some advice? Thanks alot Peter

    February 26, 2009 at 9:39 am #278493
    electrofix
    Moderator

    Re: Configuring Zanussi module

    its done by using buttons on front of machine too long winded to explain but you have to put machine into service mode and enter a hexidecimal code that is printed on the old module cover

    if you give me the product code number and an email address will send you the service manual to help unless someone else can get it to you quicker

    Dave

    February 26, 2009 at 5:20 pm #278494
    pmb
    Participant

    Re: Configuring Zanussi module

    That would be brilliant except someone really clever peeled the label off of the front of the machine with the pnc number on it so i dont have it just the model no IZ16S thanks anyway Dave 🙂

    February 26, 2009 at 5:35 pm #278495
    funkyboogy
    Participant

    Re: Configuring Zanussi module

    you need tds disk to find out config code ..
    you can also buy them pre-configured

    ally

    February 26, 2009 at 5:58 pm #278496
    electrofix
    Moderator

    Re: Configuring Zanussi module

    should not be a problem there is only 2 of them on my disk and they rpob use the same prog unit

    let me have you email address the config number is normally on the old module plastic cover

    Dave

    February 26, 2009 at 6:01 pm #278497
    pmb
    Participant

    Re: Configuring Zanussi module

    Thanks alot Dave you are a lifesaver i really appreciate this 😀
    darren_barker@hotmail.co.uk

    February 26, 2009 at 6:33 pm #278498
    electrofix
    Moderator

    Re: Configuring Zanussi module

    sorted m8 check your mail

    Dave

    March 2, 2009 at 8:06 am #278499
    pmb
    Participant

    Re: Configuring Zanussi module

    Hi Dave i haven’t received anything through yet is there any chance of you resending it thanks Peter :salute:

    March 2, 2009 at 10:27 am #278500
    electrofix
    Moderator

    Re: Configuring Zanussi module

    just seen your post will try again later when i get on the broadband

    they are big files so make sure you have room in your inbox

    Dave

    March 2, 2009 at 4:49 pm #278501
    electrofix
    Moderator

    Re: Configuring Zanussi module

    have sent again as 3 seperate emails

    Dave

    March 3, 2009 at 8:42 am #278502
    pmb
    Participant

    Re: Configuring Zanussi module

    Thanks alot Dave that is really helpful 😀

    November 6, 2013 at 8:35 am #278503
    Profyaffle
    Participant

    Re: Configuring Zanussi module

    Hi Guys,
    I’m after entering the coding sequence for Hexidecimal programming for the ZJ1217 which doesn’t have the Digital display. The last one I carried out was some years ago and can’t remember it. Help would be appreciated. Thanks

    Chris

    November 6, 2013 at 8:47 am #278504
    Martin
    Participant

    Re: Configuring Zanussi module

    Here you go…….

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)
  • You must be logged in to reply to this topic.