Scraping the barrel

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Scraping the barrel

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • April 1, 2009 at 5:50 pm #44700
    neptune
    Participant

    Had a customer ring me from London[how did he get my number]. He is looking for a wash pump[he calls it a circulation pump] for a hotpoint twintub model 9414. He describes it as an aluminium pump with a aluminium pulley that takes a round section belt. Does anyone still have one or know where I can get one please?

    April 1, 2009 at 6:17 pm #281988
    suedehead1
    Participant

    Re: Scraping the barrel

    as far as i can remember the pumps were plastic the wash pump had a flat plastic pulley which ran on the outer edge of a v belt still available from connect, the spin drain pump had a aluminiun pulley which took a thin round elasticated belt i have one of each kicking about somewhere.

    April 2, 2009 at 8:19 am #281989
    electrofix
    Moderator

    Re: Scraping the barrel

    part number 144405 obsolete asked qualtex pmp16 non gen

    also obsolete not available

    early pumps where metal top and pulley with cork gasket these used to rot through and leak

    late pumps where all plastic welded construction

    Dave

    April 2, 2009 at 9:24 am #281990
    loopey
    Participant

    Re: Scraping the barrel

    i have 1 iff needed its s/hand but looks ok

    phil

    April 2, 2009 at 10:12 am #281991
    iadom
    Moderator

    Re: Scraping the barrel

    electrofix wrote:part number 144405 obsolete asked qualtex pmp16 non gen

    Thats a wash pump, this will be a spin pump that is required for round belt pulley, part number 144406. The pumps have been all plastic for well over 25 years so the one he has must be a pattern one.

    April 2, 2009 at 10:15 am #281992
    electrofix
    Moderator

    Re: Scraping the barrel

    see what you mean just read wash pump lol


    also obsolete indesit have reassigned the part number it is now an ‘O’ ring


    Dave

    April 7, 2009 at 6:25 pm #281993
    neptune
    Participant

    Re: Scraping the barrel

    Finally managed to contact this gent again. He is old and a bit forgetful. He still maintains it is a wash pump, but I think it is a spin pump. He is now saying it is a plastic pump with an alloy wheel that takes a round section belt. If anyone has one and is willing to post it to him, would they please email me at kenliquorpond@tiscali.co.uk. witha phone number. If anyone responds and ends up out of pocket as a result, Iwill personally re-imburse them. Perhaps loopey? Thanks.

    April 8, 2009 at 3:13 pm #281994
    harley
    Participant

    Re: Scraping the barrel

    Neptune,Ive sent you a pm with my contact details,ive just dug one out my van,it’s been there for years.

    April 8, 2009 at 3:52 pm #281995
    neptune
    Participant

    Re: Scraping the barrel

    Hi harley. Many thanks but did not get your PM. Would you try again please

    April 8, 2009 at 5:42 pm #281996
    harley
    Participant

    Re: Scraping the barrel

    Neptune,replied via email address in threadmailto:kenliquorpond@tiscali.co.uk
    if its not there let me know, ill try again

    April 8, 2009 at 6:10 pm #281997
    neptune
    Participant

    Re: Scraping the barrel

    Sorry old chap, not yet received email. Please try again

    April 8, 2009 at 6:42 pm #281998
    cornwell40
    Participant

    Re: Scraping the barrel

    Didn’t one of the pumps have a black plastic cylinder which was spring tensioned against the belt 😕

    TC

    April 8, 2009 at 8:17 pm #281999
    harley
    Participant

    Re: Scraping the barrel

    Yep your right TC the wash belt is the one your descibing.
    Neptune i’ve sent another PM

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)
  • You must be logged in to reply to this topic.