Candy CDI2012 int dishwasher

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Candy CDI2012 int dishwasher

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • November 13, 2009 at 8:32 pm #50130
    scots
    Participant

    Hope someone can help.

    Problem is… machine fills then after reachine full level, VERY breifly wash motor starts then burst of water in, this cycle continues untill flood protection reached.

    I have checked prssure system and all is ok.

    Any ideas?
    or wiring diagram?

    Brian

    November 15, 2009 at 7:50 pm #303634
    leavemetogetonwithit
    Participant

    Re: Candy CDI2012 int dishwasher

    Cannot find the model on Connect but looking at diagram of CD242UK it looks like the p/sw tube might be running from the circulation pump outlet point ❓ . It’s a long shot, but if for some reason the motor were revolving in the wrong direction, I could imagine this would result.
    Mike.

    November 15, 2009 at 9:06 pm #303635
    timdowning
    Participant

    Re: Candy CDI2012 int dishwasher

    Is it similar to this?

    http://www.ukwhitegoods.co.uk/modules.php?name=Forums&file=viewtopic&t=47090&highlight=hoover+dishwasher+fill

    No conclusion as of yet but may be worth re-opening?

    November 16, 2009 at 1:05 am #303636
    Penguin45
    Participant

    Re: Candy CDI2012 int dishwasher

    You’ll probably need a p/sw and a circ pump….

    Chris.

    November 16, 2009 at 7:12 am #303637
    Lawrence
    Participant

    Re: Candy CDI2012 int dishwasher

    I had one of these doing the same ,I told the customer to go to hvr/candy and would they let me know the outcome .
    You will love this …
    He fitted pcb,motor,p/switch,door switch ,base float ,heater safety device and it still didn’t work ,she bought a new one in the end .
    She had the impression that he wasn’t quite sure what it was …

    November 16, 2009 at 9:16 am #303638
    scots
    Participant

    Re: Candy CDI2012 int dishwasher

    Thanks for replies.. The clicking that you hear is def the heater protection switch (located at the rear base) , switching when the circ motor starts.

    From what I see, it looks like it may be the board, although the motor fitted looks like the one fitted to the Whirlpool/Diplomat dishwashers and we all know how they fail!

    Its just that the motor does start albeit breifly and why is it the inlet valve operate breifly?

    Going to return to get product code, as there are 3 different modules.
    Will let you know

    Brian

    December 2, 2009 at 1:09 am #303639
    bmrenr
    Participant

    Re: Candy CDI2012 int dishwasher

    Hi Brian how did you get on with this as I have the same prob with one of these.
    Tom.

    December 2, 2009 at 9:57 pm #303640
    scots
    Participant

    Re: Candy CDI2012 int dishwasher

    Sorry Tom but customer has had the dishwasher replaced

    Good luck with yours and if you resolve it please post so we can all gain ?

    Brian

    December 2, 2009 at 10:57 pm #303641
    alster
    Participant

    Re: Candy CDI2012 int dishwasher

    Had the same fault with one of these & new pcb cured the fault.

    December 3, 2009 at 12:19 am #303642
    Cras
    Participant

    Re: Candy CDI2012 int dishwasher

    and me pcb cured my fault as well 😀

  • Author
    Posts
Viewing 10 posts - 1 through 10 (of 10 total)
  • You must be logged in to reply to this topic.