Neff T4543N1/09

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Neff T4543N1/09

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • December 11, 2009 at 9:08 am #50871
    clayside
    Participant

    Having trouble the this induction hob. Will not turn on sometimes, sometimes comes on then as you select heat turns off , then few seconds later flashes E’s in every display, sometimes timer comes on without being set. Glass is clean and have cleaned it again to be sure. Have changed the front control board but still the same. Hand book says if E’s flash glass is dirty but this isn’t. Trouble is getting worse. Any ideas please.
    clayside

    December 11, 2009 at 2:20 pm #306200
    lee8
    Participant

    Re: Neff T4543N1/09

    Error E is Sensor button continuously actuated.

    You need to ensure the glass is clean top and bottom and the sensor also.

    Damp can also cause it, so ensure the foam seal around the outer rim of the glass is in place.

    If nothing else all you can do is point the client to section 7.26 of there user manuel instructing them about E errors and walk away as there is not fault.

    You didn`t design it and you didn`t buy it, so you`ll need to point out its something that cannot be fixed as its a design feature and crap.

    You cannot fix something that can`t be fixed. 😉

    December 11, 2009 at 2:23 pm #306201
    lee8
    Participant

    Re: Neff T4543N1/09

    ops double posted, sorry.

    December 11, 2009 at 7:20 pm #306202
    clayside
    Participant

    Re: Neff T4543N1/09

    Thanks Lee,
    Will call back check and advise. The underside of the glass appears to have a very thin film which looks like silicon which covers the area where the sensor buttons go, should ths be their or should I scrap it off. It looks like it should be their as it has straight edges etc.It is only at front of glass.
    Regards
    clayside

    December 11, 2009 at 7:44 pm #306203
    lee8
    Participant

    Re: Neff T4543N1/09

    It should be there and check in case bits are missing, it helps the electronics recognise your pinkies.

    December 11, 2009 at 8:03 pm #306204
    clayside
    Participant

    Re: Neff T4543N1/09

    I don’t think it is covering evenly over area, whap is it ? can I repair/replace it.
    clayside

    December 13, 2009 at 11:44 am #306205
    PINKY
    Participant

    Re: Neff T4543N1/09

    Its put on in the factory so DON’T mess with it. Sound like the Ellin pcb to me.Left hand side controls both. Loads of money!!!!

    December 13, 2009 at 1:33 pm #306206
    clayside
    Participant

    Re: Neff T4543N1/09

    Thanks Pinky& Lee,
    Me thinks Iwill hand this over to BSH or may get my fingers burnt buying parts that are not required.
    Regards.
    clayside

    December 13, 2009 at 3:15 pm #306207
    lee8
    Participant

    Re: Neff T4543N1/09

    Control PCB around £240.00, right board around the same and left one around £150.00

    Glass top £160.

    Its expensive to get wrong.

    .

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.