BEKO WMA 520S

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › BEKO WMA 520S

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • April 8, 2010 at 5:19 pm #53853
    funkyboogy
    Participant

    after cycle ends > door unlocks after about 10 seconds locks again and cycle starts up on orig cycle..

    bit of a strange one … i have changed pcb but didnt cure prob ,

    thought i had a faulty pcb so i changed it … but no still same fault ..

    any ideas

    ally

    April 8, 2010 at 9:31 pm #317471
    Allsorts
    Participant

    Re: BEKO WMA 520S

    Start button short?

    April 8, 2010 at 9:42 pm #317472
    leavemetogetonwithit
    Participant

    Re: BEKO WMA 520S

    Isn’t the start switch part of the pcb? Maybe the button is sticking? So needs cleaning and lubricating.
    Mike

    April 9, 2010 at 8:04 am #317473
    funkyboogy
    Participant

    Re: BEKO WMA 520S

    sorry guys , should have mentioned ….

    start button is part of pcb and works perfectly ..i thought that at 1st as well but if start button stuck in prog would have started and then cancelled if you get what i mean ..

    its a strange one , as wm works perfectly but customer has to be there when it ends so she can switch off at plug ..

    i thought she was taking the p , but seen it myself ..

    any furhter ideas , appart from hammer etc ???

    cheers

    April 9, 2010 at 10:23 pm #317474
    leavemetogetonwithit
    Participant

    Re: BEKO WMA 520S

    Well, she could time how long her usual programme takes and then use it with one of those plug in digital timers which I think can be set to run to the minute. And they’re only about seven quid.
    Mike.

    April 9, 2010 at 10:29 pm #317475
    bigchrisoioi
    Participant

    take it outside and burn it!!!, claim on the insurance !! lol

    April 10, 2010 at 9:20 am #317476
    DDSDDS
    Participant

    Re: BEKO WMA 520S

    maybe the machine is a perfectionist and was just not happy with the wash and felt the need to do it again


    as for the fault at this point i would be inclined to start taking off every part whilst scratching my head

    April 10, 2010 at 10:56 am #317477
    TheSpinDoctor
    Participant

    Re: BEKO WMA 520S

    Hi.

    Have you entered the diagnostic to retrieve the last recorded fault code?

    April 10, 2010 at 3:08 pm #317478
    iadom
    Moderator

    Re: BEKO WMA 520S

    I had a similar fault on an BEKO based ISE machine. Got to end, door unlocked then relocked again after a few seconds. Removing the mains plug was the only way to get the door open.

    Turns out it had had some dodgy brushes fitted ( not by me 😉 ) and the arcing was corrupting the PCB.

    I had to replace the motor due to severe armature damage.

    April 11, 2010 at 8:38 am #317479
    funkyboogy
    Participant

    Re: BEKO WMA 520S

    i will have a look at motor ..

    dont kn ow how to enter diag ..can you please advise

    cheers ally

    April 11, 2010 at 9:13 am #317480
    TheSpinDoctor
    Participant

    Re: BEKO WMA 520S

    Hi.

    Check your PM’s.

    April 12, 2010 at 5:56 pm #317481
    funkyboogy
    Participant

    Re: BEKO WMA 520S

    cheers for extra info , will update as soon as get to bottom of prob

    ally

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.