Admiral AC 2224 GEKB F/Frez

This topic has 10 replies, 4 voices, and was last updated 15 years, 8 months ago by a1al.

Viewing 11 posts - 1 through 11 (of 11 total)

Author

Posts
August 11, 2010 at 8:28 pm #56463

a1al
Participant

Hi Everyone

Have not worked on this brand of F/Frezzer before, any help would be great.
When switched on at the plug the compressor and condensor fan run for only a few seconds then turn off and do not come back on even when left on all day. Adjusting the stats has no effect.
(Serial No 11705649JR)

Anyone any ideas ??

al

August 12, 2010 at 3:54 pm #327507

ELDAR59
Participant

Re: Admiral AC 2224 GEKB F/Frez

probably the pcb mate, especially if the condenser fan and compressor run when you open the fridge door and then cut out when you close it.

cheers.

August 13, 2010 at 1:58 pm #327508

a1al
Participant

Re: Admiral AC 2224 GEKB F/Frez

thanks for that, alf_uckem

Do you know of a supplier who would stock this pcb or where I could check for a Part Number

Al

August 13, 2010 at 4:22 pm #327509

ELDAR59
Participant

Re: Admiral AC 2224 GEKB F/Frez

hi mate, part no 12868513.
available from maytag, their number is 0844 499 0101.

cheers.

August 16, 2010 at 12:13 pm #327510

a1al
Participant

Re: Admiral AC 2224 GEKB F/Frez

Thanks again,

Al

August 27, 2010 at 1:35 pm #327511

a1al
Participant

Re: Admiral AC 2224 GEKB F/Frez

Hi Guys

Have recieved part from Maytag or should I say Parts because they have sent me two boards with a note saying that the LV Board and HV Board have to be changed at the same time as there can be possible incompatibility issues.

The only part numbers I can find are HV Board 12639501 and
LV Board 67003751

Also I have read on some posts about coding these PCB, does anyone know how this is done.

Many Thanks

Al

August 28, 2010 at 8:15 am #327512

burns
Participant

Re: Admiral AC 2224 GEKB F/Frez

Hi.
Something has gone wrong here, It sounds like they have sent you boards for the older Amana XRSS. What you need is the Control board http://lookup.partadvantage.com/lookup/maytag/6153/00040394#Its located in the top of the fridge section and can be removed by three or sometime four screws into the roof.
There are three types currently available, you can identify then by the sticker on the board. Jazz 14 – 15 and 16
For some reason there is a big price difference. The jazz 14 is half the price of the other two.
If you need any more info go to:- http://www.servicematters.com and click on the tab for old Maytag service library. You can then input the model number and get tech info.
It will need programming, but depending which board, the code is on the rating plate inside the fridge. This is shown as code. If all else fails code 05 works pretty well.
Either way these will be much cheaper than what you have been sent if theyve invoiced for the boards youve been sent. :rolls:

August 28, 2010 at 12:09 pm #327513

a1al
Participant

Re: Admiral AC 2224 GEKB F/Frez

Hi Burns

Thanks for your reply information very helpful,
will contact Maytag on Monday to try and sort out parts mix up

Thanks again

Al

August 28, 2010 at 12:54 pm #327514

funkyboogy
Participant

Re: Admiral AC 2224 GEKB F/Frez

connect do them
MTG12868513 65.63 + vat

dont know if thats expensive or not compared to maytag …

05 CODE works a dream .. ivenever managed to code 1 with its own code yet ..

August 28, 2010 at 3:07 pm #327515

a1al
Participant

Re: Admiral AC 2224 GEKB F/Frez

Thanks for that funkyboogy I’ll make sure and use 05 when coding the new PCB

a1al

September 7, 2010 at 7:43 pm #327516

a1al
Participant

Re: Admiral AC 2224 GEKB F/Frez

Hi Guys

Just to let you all know been back today and replaced PCB (12868513) job done, and it would not accept code 28 as per label so used code 05 and it worked a treat, another success for UKWG’s.

Many Thanks

Al
Author

Posts

Viewing 11 posts - 1 through 11 (of 11 total)

You must be logged in to reply to this topic.