Hotpoint/Creda WM dispenser drawer.

Home › Forums › Trade Technical & Spare Parts Forums › Trade Spare Parts › Hotpoint/Creda WM dispenser drawer.

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • February 3, 2011 at 4:40 pm #60759
    iadom
    Moderator

    Machine is actually not that old. A Creda W120VW in almost perfect condition.

    Not a fault I have come across before, it is leaking from the welded seam along the back of the outer soap drawer.

    This type of dispenser does not split into two halves and will be very difficult to seal.

    Part sadly is listed as obsolete.

    Does anyone have an old, good outer dispenser drawer for the later WM range they would be willing to let me have for a reasonable consideration?

    If possible I would prefer the later type with the totally welded top rather than the earlier 9000 series that had the rectangular air break on the top at the back of this drawer.

    Jim.

    February 4, 2011 at 10:36 am #343498
    iadom
    Moderator

    Re: Hotpoint/Creda WM dispenser drawer.

    BUMP. 🙂

    Is there no one who can make a dear old lady or for that matter an old washerman happy. ❓

    Jim.

    February 4, 2011 at 11:15 am #343499
    Martin
    Participant

    Re: Hotpoint/Creda WM dispenser drawer.

    You might just be able to open the split seam sufficient to apply Evostik Pipe Weld adhesive (or similar plastics fusing adhesive) to rebond it? 💡

    February 4, 2011 at 4:02 pm #343500
    iadom
    Moderator

    Re: Hotpoint/Creda WM dispenser drawer.

    I did toy with that possibility but the position of the split, right at the back corner near the inlet tubes would make it very difficult. 😥

    Also the machine is in an upstairs flat so job has to be 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} kosher, can’t risk it not sealing properly. 😉

    Jim.

    February 7, 2011 at 10:17 am #343501
    iadom
    Moderator

    Re: Hotpoint/Creda WM dispenser drawer.

    Early morning thread bump. 😉

    February 7, 2011 at 6:35 pm #343502
    DAR01
    Participant

    Re: Hotpoint/Creda WM dispenser drawer.

    I’ve definitely got an outer WM dispenser if you still need one will check tomorrow, PM me with your contact details, you can have it for the cost of the postage.

    Mike

    😀 😀 😀

    February 7, 2011 at 6:36 pm #343503
    iadom
    Moderator

    Re: Hotpoint/Creda WM dispenser drawer.

    That would be fantastic if you do have one, will you be at the meeting in Coventry, I could get you a couple of jars at the very least.

    I will PM you my details.

    Thanks.

    Jim.

    February 7, 2011 at 8:32 pm #343504
    johnnyj
    Participant

    Re: Hotpoint/Creda WM dispenser drawer.

    I might have one lying about i’ll check tomorrow.J

    February 8, 2011 at 4:31 pm #343505
    DAR01
    Participant

    Re: Hotpoint/Creda WM dispenser drawer.

    It’s in the post 1st Class, hope it’s the right one.


    Mike

    😀 😀 😀

    February 8, 2011 at 5:00 pm #343506
    iadom
    Moderator

    Re: Hotpoint/Creda WM dispenser drawer.

    I will let you know ASAP. 8)

    February 11, 2011 at 8:35 pm #343507
    iadom
    Moderator

    Re: Hotpoint/Creda WM dispenser drawer.

    Part arrived today Mike, will sort out the funds ASAP, thanks very much and thanks also for all the other offers. 😀

    Jim.

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.