- This topic has 17 replies, 4 voices, and was last updated 14 years, 11 months ago by
.
-
Posts
-
Hi,
I have an intermittent (has been going on for 6 months or more) problem where upon starting the dishwasher stops after 10 mins or more and beeps. The lights flashes 7 times before a pause. It never gets past popping the tablet. Sometimes I can get it to work by switching off and restarting but now nothing I do will get it to work I am about to call an engineer. However looked on this forum and can see it possibly is the water chamber. Can you help with this?If so where is the water chamber located in the dishwasher -i know its in the side panel but is that accessed by pulling machine out and taking of the right or left side or is it in the door?
Thanks in advance for any help
emma
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
It’s telling you there’s a problem with the flow meter which is built into this fill chamber.
K.
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
thanks alot, do you know which side panel it is located in or is it in the door?
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
I think it’s in the right hand side buried between the outer panel and the inner tub.
K.
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
Hi,
Thankyou I ordered the part and have fitted it…but I appear to have damaged the white circular disc that holds the seal in place of the refill unit. It now leaks and I suspect it is because of this.. 😥 (You can see it inside the dishwasher on the inner left hand side of you are looking at the dishwasher open). I have attached an image, I don’t suppose you know if I can buy this part?
Thanks alot
Emma
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
Ouch, no, it’s a full assembly I’m afraid the bits can’t be gotten separately. 🙁
K.
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
oh dear thats the last time my husband lets me near the insides of a machine!! 😆 By full assembly do you mean the internal door or a new machine?! In your opinion is it a write off now?
Thanks
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
You get 1 of these rings on the new part and you should still have the 1 that you removed… I cant believe Ken is responding to a post where customer thinks flow meter is possibly in the door….should of suggested an engineer visit to effect a safe and tested repair. All probability was the read switch which cost about £4
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
I have broken the one I removed, can you tell me with which new part I get one of these rings? I didn’t get a new ring with the fill chamber? Will it still be cost effective to repair or should I just get a new dishwasher?
Many Thanks for you response
emmaRe: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
Hi embr,
As I said, you can’t get the part separately from the chamber itself, it’s only sold as a complete unit. 😕
K.
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
Hi Kwatt,
Yes I understand that I cannot buy the part separately, but which complete unit do I need to purchase. When you say a complete unit do you mean a new dishwasher or can you point me in the direction of the what I need to order? Sorry if I am not being clear!
Thanks
embrRe: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
reg.dosage with flowmeter is what the complete part is called,if u supply ur 85 number sited on the right hand side of the dishwasher door “metal door”i could give u the part number 😀 hope this helps.
Re: Whirlpool ADG 7440 Erro continuous beep 7 flashes with p
Ah, the penny’s dropped.
I thought you meant the bit on the side chamber but this is the one on the inside of the dishwasher, yes?
If that’s correct then the part number is 481246278994 but it’s coming up as being obsolete. 🙁
I’ve sent an email to double check it for you.
K.
- You must be logged in to reply to this topic.