Zanussi WJS1265W washing machine

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Zanussi WJS1265W washing machine

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • January 4, 2005 at 11:08 am #7304
    roly16
    Participant

    This machine cuts out a few seconds after starting to fill. The test program is showing an error [at first briefly E35] but now only E31, an ‘analogic pressure switch’ problem according to the error code list. It’s not clear from the flowchart how to test this device properly; does anybody know? The pressure tubes are clear and the cable from the switch to the board is ok. The ordinary pressure switch is working normally except that level 2 operates just before level 1, but the machine stops filling before the water level is high enough to operate it. Can anybody suggest what’s happening here? Many thanks, Geoff.

    January 4, 2005 at 1:02 pm #122580
    Dave_Conway
    Participant

    Re: Zanussi WJS1265W washing machine

    Have you got the TDS disk Geoff ?

    Have a look at the troubleshooting guide, there’s a bit there about these analogic switches.

    I found this bit:

    Measure a close circuit between J4-3,
    J4-4 and J4-5 and the 3 connector on
    analogic pressure switch plug (they are 3
    independent connections)
    Is the cable between main board and
    analogic pressure switch OK and
    connected correctly on both sides?

    Dave.

    January 4, 2005 at 5:11 pm #122581
    roly16
    Participant

    Re: Zanussi WJS1265W washing machine

    Hi Dave , thanks for the reply. Yes I’ve got the TDS disc and I had found that but it doesn’t seem to make a lot of sense when you’re looking at the switch. Icertainly don’t get a ‘close circuit’ when testing across the switch contacts but an open circuit, so I suspect this is the problem. I was just hoping for confirmation from someone familiar with the problem. Geoff

    January 4, 2005 at 10:36 pm #122582
    admin
    Keymaster

    Re: Zanussi WJS1265W washing machine

    I had a fault on a similar machine. It would lock the door, briefly fill then unlock the door. Same fault code too and I did check pressure hoses, all were ok. Changed main module ( you will need coding sheet if not pre coded); and all worked fine. Hope that helps. 😉

    January 4, 2005 at 10:46 pm #122583
    Dave_Conway
    Participant

    Re: Zanussi WJS1265W washing machine

    gegsy, where the hell did you get that avatar ? :rotl:

    Dave.

    January 4, 2005 at 10:46 pm #122584
    roly16
    Participant

    Re: Zanussi WJS1265W washing machine

    Hi Gegsy,
    Thanks for that. I’ll let you know what transpires.
    Geoff

    January 4, 2005 at 10:48 pm #122585
    admin
    Keymaster

    Re: Zanussi WJS1265W washing machine

    Dave_Conway wrote:gegsy, where the hell did you get that avatar ? :rotl:

    Dave.

    You never met the misses dave lol 😳

    January 4, 2005 at 10:52 pm #122586
    admin
    Keymaster

    Re: Zanussi WJS1265W washing machine

    roly16 wrote:Hi Gegsy,
    Thanks for that. I’ll let you know what transpires.
    Geoff

    No probs Geoff, good luck

    January 4, 2005 at 10:58 pm #122587
    Dave_Conway
    Participant

    Re: Zanussi WJS1265W washing machine

    gegsy wrote:You never met the misses dave lol 😳

    I don’t think I want to if that’s what she does to people 😯 😆

    January 6, 2005 at 10:19 pm #122588
    roly16
    Participant

    Re: Zanussi WJS1265W washing machine

    That’s not Gegsy’s wife, that’s gegsy dealing with an awkward customer.

  • Author
    Posts
Viewing 10 posts - 1 through 10 (of 10 total)
  • You must be logged in to reply to this topic.