hotpoint sdw80 dishwasher

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › hotpoint sdw80 dishwasher

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • January 19, 2013 at 11:45 am #73635
    seanmfc
    Participant

    hi all
    about june 2011 i had the error code al10 come up on my hotpoint sdw80 dishwasher with advice from here i replaced the heating element and it worked today the code has come up again is there a good bet its gone again

    thanks

    January 19, 2013 at 1:33 pm #388236
    iadom
    Moderator

    Re: hotpoint sdw80 dishwasher

    The only way to find out is to test the element with suitable test equipment. The main pcb is just as likely to cause this fault so if the element is OK then it’s 95{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} certain the module has failed. 🙁

    January 21, 2013 at 4:38 pm #388237
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    ok do you test the 2 prongs to get a reading or do you have to use earth if its the 2 prongs i have a reading that was done on 2 setting 0.28 ohms

    January 21, 2013 at 4:44 pm #388238
    iadom
    Moderator

    Re: hotpoint sdw80 dishwasher

    Prongs????

    You test between the two teminals that the wiring harness plugs into, resistance should be 26.5?.

    Not sure what you mean by ‘2 setting’. ❓

    January 21, 2013 at 5:39 pm #388239
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    i cant put a photo on here yhe multimeter is a rapitest and starts 2 v k ohms sign then 20 v k ohms sign then
    200 v k ohms m a then 500v 2000 k ohms the button at the top is set to ohms and the dial is on 2 any other settings i dont get any reading

    January 21, 2013 at 5:47 pm #388240
    iadom
    Moderator

    Re: hotpoint sdw80 dishwasher

    Looks like the heater may have died again, set your meter to 500v and you should get a reading of 26.5 ohms.


    Sent from my iPad using Tapatalk HD

    January 21, 2013 at 5:52 pm #388241
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    i just did what you said and have a reading of 0.00

    January 21, 2013 at 6:12 pm #388242
    iadom
    Moderator

    Re: hotpoint sdw80 dishwasher

    Ergo duff heater. 😉

    January 21, 2013 at 6:30 pm #388243
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    thanks for your help

    January 23, 2013 at 4:13 pm #388244
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    i have fitted the part but after a few min working the electrics tripped out im hoping it was a bit of excess water so im going to leave it a few days

    January 26, 2013 at 11:20 am #388245
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    right i left the dishwasher off for a few days as i thought athere was a bit of excess water that tripped the electrics

    when turning the electric back on everything tripped out again can i have put any wires back wrong im thinking thr connector at the very bottom plate is round the wrong way

    February 3, 2013 at 6:51 pm #388246
    seanmfc
    Participant

    hotpoint sdw80

    hi
    i recently fixed the al10 code now i have a al05 pump code but when i turn the machine off it returns itself back on

    any ideas

    February 3, 2013 at 8:17 pm #388247
    iadom
    Moderator

    Re: hotpoint sdw80 dishwasher

    Hard to know what if any problems you may have caused with your previous repairs TBH..
    A05 is supposed to be blocked filters, pressure switch faults or main circulation pump faulty.

    Merged your posts as well, best to kep it all in one place for continuity. 😉

    February 23, 2013 at 1:16 pm #388248
    seanmfc
    Participant

    Re: hotpoint sdw80 dishwasher

    i have checked for any blockage and found none put into a 1.33 cycle and the fault codes have come up again im now going to give up the ghost now on this

    does anyone know where i can get a decent slimline washer for under £300

  • Author
    Posts
Viewing 14 posts - 1 through 14 (of 14 total)
  • You must be logged in to reply to this topic.