- This topic has 8 replies, 2 voices, and was last updated 13 years, 1 month ago by
.
-
Posts
-
pnc: 91123251701
This machine previously had a fault that for reasons not fully clear was rectified after refitting the controller connections. Subsequently has worked fine for two months till a few days ago when the 30minute wash was pressed instead of the intensive 70deg wash. The finger doing the pressing realized the mistake and immediately pressed the 70 button. The result was no washing and the wash and dry leds coming on (flashing).
Situation now is that on power up mains light on, no other lights (for about 4 seconds) then wash/dry leds flash, followed by pump out (twice) then nothing other than the steady flash of the leds which continue until machine switched off (several hours).
If on power up a program button is pressed before the other two leds flash, then the program light is initially steady but then also flashes and pump out cycle commences as above.
There has been no leakage, machine is dry, the switch on the flood float clicks when the float is raised, the water control pressure switch operates fine and tube to it is not blocked. Drain system and pump are fine. Wiring and connections through door and in base looks in good condition, no abrasion or marking showing.
Any ideas appreciated.Many Thanks.
Re: AEG F50730 not working.
We need to know which lights, they are detailed as follows…
1 – 4
2 – 5
3 – 6Or,
1 – 2 – 3 – 4 – 5 – 6
The software functions can be changed from model to model so the documentation is generic.
K.
Re: AEG F50730 not working.
Thanks for prompt response, the led’s are arranged:
1 – 4
2 – 5
3 – 6Module is type EDW110 ref 111578302, Bitron Code 01305627500.
Sorry for not giving full details originally.regards
Re: AEG F50730 not working.
Can you tell us which ones are flashing using the numbers, the function of each is irrelevant really and we can’t map it that way.
K.
Sent from my iPad using Tapatalk HDRe: AEG F50730 not working.
Buttons are arranged
1 – 4
2 – 5
3 – 6
1,2,3,5,6 have adjacent LED’s (normally wash programs), 4 (delay timer) has three leds depending on time set.
to the right of these are five more led’s arranged:
7
8
9
–
10
11
7,8,9 are described in the book as ‘multi function display’, 10 and 11 as ‘control indicators'(salt/rinseaid)On power up: After about 4 seconds leds 7 & 8 flashing
On power up and pressing any program button (1,2,3,5,6) immediately :respective program led steady, then 7 & 8 leds flashing, program led changes to flashing at same time. Flash rate about once per second.Thanks
Re: AEG F50730 not working.
Sounds like the Aquastop has been activated meaning that there’s a leak into the base or, the float system or fill detection is faulty in some way.
While that error is there it won’t go.
Cycling the power is the reset so it’s obviously not a simple reset.
K.
Re: AEG F50730 not working.
Yes, Certainly no fill water coming in. The base is completely dry (checked within 20minutes of the fault occurring, so not time for it to have dried out) and the float switch is sounding OK when the foam float is lifted from the base.
Wiring for the switch is more difficult to access, but is worthwhile checking further. I assume that the level control is limited to the pressure unit on the right side, this has been checked and again, from the clicks of the contacts when gently blown into, seems OK, but I will check this further. The connection pipe is clear and correctly routed. The large plastic water ‘matrix’ on the left is completely clean with water holding just below the air break at the top.
Thanks.Re: AEG F50730 not working.
No clue, I’ve never worked on one, I was just trying to let you know what the fault code was. 😉
K.
Re: AEG F50730 not working. RESOLVED
Reading back through posts and the AEG user book (really desperate)I concluded that with assurances the control module was unlikely to be at fault. Knowing there was no water under the float and the switch was clicking nicely when the float was operated, I thought that the float and inlet ‘Aqua stop’ valve must be linked directly as the book says antiflood is active even if no program is running. Did a resistance check on the inlet valve and found this open circuit. Replaced the hose and valve and no more problems noted. One wash down, hopefully many more to go.
Thanks for assistance
- You must be logged in to reply to this topic.