LG WM-1465FHD

Home › Forums › Public Support Forums › Help And Support › Washing Machine Help Forum › LG WM-1465FHD

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • January 24, 2005 at 11:15 pm #7622
    admin
    Keymaster

    Hi guys,

    You all helped me before when I had a problem with this bloody washing machine, hopefully you will be able to again!

    This time I have an FE error code…

    It seems that during the spinning cycle a slow flow of hot water flows through the draw and into the drum… at first I thought it was a pump blockage as all the clothes were wet at the end of the cycle. But I checked that out and I am £1.70 richer from my finds in the filter, but it has not solved my problem! I have to keep switching off the hot tap and re-spinning!

    Any help would be gratefully received.

    Thanks

    Charlie

    January 25, 2005 at 12:09 am #124313
    Penguin45
    Participant

    Charlie,
    Check whether you have a hot water fill all the time or only on the spin sequence. The former would indicate a weeping valve, the latter a problem with the electronics.

    Regards,
    Penguin45.

    January 25, 2005 at 9:05 am #124314
    admin
    Keymaster

    Re: LG WM-1465FHD

    this fault will be caused by 2 parts normally and the most likely one lies within the hot water valve or cold water valve seeping and allowing water into the machine when switched off.

    if the machine does not fill when switched off for 2 days then the fault would normally be the main PCB alowing current to the valve.

    hope this helps

    bryan

    January 25, 2005 at 8:43 pm #124315
    admin
    Keymaster

    Re: LG WM-1465FHD

    Hi guys,

    Thanks for the reponses.

    The water does not flow if the machine is switched off. I check to see if the water flows only on spin…

    if it is electronics, is there a way of defaulting it? or reseting it??

    Thanks again

    Charlie

    January 26, 2005 at 4:32 am #124316
    admin
    Keymaster

    Re: LG WM-1465FHD

    Sorry but if the water is passing through the valve due to electric current going to the valve during spin then you oly have 1 option and that is a new PCB.

    the part number for this is a choice of 3 (they are all the same pcb )

    6871EC1024R OR 6871EC1024D OR 6871EC1077D

    I have one these in stock

    hope this helps

    bryan

    February 7, 2005 at 8:29 pm #124317
    admin
    Keymaster

    Re: LG WM-1465FHD

    hmmmm i guessed as much…

    is it easy to fix??

    how much is a new PCB?

    It wouldnt be a stuck valve would it??

    February 7, 2005 at 9:48 pm #124318
    SparkyP
    Participant

    Re: LG WM-1465FHD

    Hi Charlie,
    It is a characteristic of this machine. When on Final spin it will open the valve and fill with water but only for a few seconds. This is normal. You have checked the filter but i would have a closer look at the impellor in the filter housing at the back. Switch off at mains then tilt the machine back then open the filter and carefully with a screwdriver try to turn the green impellor at the back. It is common to get things caught in these. As for the error code FE this is not listed in the service manual.
    Hope this helps

    Sparkyp

    February 8, 2005 at 4:41 pm #124319
    SparkyP
    Participant

    Re: LG WM-1465FHD

    Hi Charlie again,
    After much searching i have the code for the FE display error. It means that the water overfills due to the faulty water valve.

    Hope this helps
    Sparkyp

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.