- This topic has 12 replies, 2 voices, and was last updated 11 years, 9 months ago by
.
-
Posts
-
Hello
Anybody have table of error codes for dishwasher BEKO 6837x ?
Dishwasher starts normally, after pull-in water stops and don’t start washing process. The ” : ” in timer displays hangs (stop bliking). After RESET – water is pumping out with no problem.
I’ve check:
-computer (central module) – second piece have the same problems.
-checking hoses, water supply etc – all ok, clear.
-service mode given me error: “Er:2”Additional info:
-electrovalve have “tapping sound” – every few seconds i hear it, i don’t know this sound before but maybe i did not notice it.Any idead ?
Regards,
Kane
Re: BEKO 6837x error codes
thx ! dishwasher gets water, I try before replace “watercounter” but with no effect. Service guy – fail (no effect, don’t have a clue about this) – i must fight alone with this :/
Is there any sensor for water-level ? Where in this dishwasher ? How I may test it ?
And:
“Additional info:
-electrovalve have “tapping sound” – every few seconds i hear it, i don’t know this sound before but maybe i did not notice it.”This 3-way valve (electrovalve) working but have some tapping sound – this is normal ? Like work of clock or smth…
Regards,
Kane
ps. sorry for my terrible english 😉
Re: BEKO 6837x error codes
you are sure there is water to the machine. dont trust the tap take hose off machine and check for good water flow
Dave
Re: BEKO 6837x error codes
yeah, tested. Hose ok – clear.
dishwasher gets water normally but somehow central module does not know about it and main wash process not starting.
Swap of “flow meter” (waterclock?) -> http://www.klinikaagd.pl/foto/beko_1729900100.jpg
– same effect, same error.
Today last thing – cables, maybe some electric cable have pause (is break) and central module does not know about water – this flow meter is ONLY thing that inform central module about how much water is in dishwasher ?Re: BEKO 6837x error codes
Hello again !
Thanks for last help for me – in problem from 2014 year that was broken cable (break) to flowmeter. I fix it and dishwasher works ok…until today. So…almost year !Today i have E1 error code and dishwasher did not remove water (and therefore don’t start any washing program) , i check filter nad hose – all ok.
Best regards from Poland !
Re: BEKO 6837x error codes
update:
after removing small portion of water from base of dishwasher (dishwasher rotate to side for 1 hour)…dishwasher starts (in test-mode), make some test etc but pause after few minutes with error Er:4
after opening the door – water in dishwasher.Re: BEKO 6837x error codes
hello again
my Beko still lives ! 😉
New year, new problem:
– dishwasher shorts time of program, ie program have 1:05 duration but ends with ~40m, without errorSelf-test of dishwasher: Er:4 Er:6
Have you information what this errors means ? I cannot find proper error-code table for this dishwasher
Re: BEKO 6837x error codes
ah, maybe important:
– the dishwasher pill (chem used to dishwashing) is not completly dissolve, only partial.
Rest is in interior of dishwasher.Re: BEKO 6837x error codes
I have the same problem as last time your model is not correct
list full model
there is also a number beginning with a 7 which is also a modelDave
Re: BEKO 6837x error codes
stil cant find exact model but from what I can see of model numbers close
are you in the uk ?
Er:4 Turbidity Sensor Fault (if applicable)
Er:6 NTC FaultDave
Dave
- You must be logged in to reply to this topic.