Confused Beko DWD4311

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › Confused Beko DWD4311

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • September 28, 2014 at 8:03 am #82395
    88tinkler
    Participant

    Dishwasher completes cycle to end but does not pump out rinse water despite pumping out mid cycle. Repair man said he thought circuit board had gone therefore not worth repairing. (machine is three years old). Obtained correct circuit board myself and fitted without difficulty but it has made no difference. Any suggestions folks?

    September 29, 2014 at 11:37 am #419719
    nigegt
    Participant

    Re: Confused Beko DWD4311

    The main circuit board is only about £30. Must be worth that.

    October 1, 2014 at 9:27 pm #419720
    88tinkler
    Participant

    Re: Confused Beko DWD4311

    Thanks for response, but I bought the circuit board and fitted it without difficulty but it has not solved the problem

    October 2, 2014 at 7:07 am #419721
    Martin
    Participant

    Re: Confused Beko DWD4311

    I know this sounds blindingly obvious but have you checked the pump properly??? At 3 years old it must be clapped out by now.

    October 2, 2014 at 8:56 am #419722
    Seamy
    Participant

    Re: Confused Beko DWD4311

    Do you know if it had heated?
    Have had problems on them with small cable to heater thermistor & water counter going open circuit in loom at bottom of door.
    Loom to pump could be on the way out either or pump going o/c when hot.

    October 6, 2014 at 10:49 am #419723
    88tinkler
    Participant

    Re: Confused Beko DWD4311

    Thanks for help. Yes everything works OK apart final pump out. Only other symptom is a noise as if pump is operating in a series of bursts part way through.

    October 6, 2014 at 5:05 pm #419724
    Seamy
    Participant

    Re: Confused Beko DWD4311

    Agree with Martin then, likely the pump is buggered or summit stuck in it, piece of broken crockery, glass, bone, sweetcorn kernel etc.

    October 6, 2014 at 6:57 pm #419725
    lee8
    Participant

    Re: Confused Beko DWD4311

    Check regeneration tank valve. It’ll fill on final rinse, then wait for valve to pass water through, it won’t drain until that completes.

    October 6, 2014 at 7:04 pm #419726
    lee8
    Participant

    Re: Confused Beko DWD4311

    It may look like the photos or a simple resistance test will suffice .

    October 11, 2014 at 3:36 pm #419727
    88tinkler
    Participant

    Re: Confused Beko DWD4311

    Thanks for helpful response Lee. Bit of an amateur here. Don’t know what regeneration tank valve looks like nor where to find it. Few pointers would be much appreciated.

    October 11, 2014 at 11:28 pm #419728
    lee8
    Participant

    Re: Confused Beko DWD4311

    Take the base off, it’s attached to the salt container and has two wire connectors, looks the same as the valve your fill hose screws onto. The photos I’ve put here are of your model, so it’ll help to identify.

    October 12, 2014 at 9:12 pm #419729
    88tinkler
    Participant

    Re: Confused Beko DWD4311

    Very grateful for your help Lee. As soon as I get a few minutes I’ll be having a look. 🙂

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.