VT1014D23 – runs for 4 seconds at a thim

Home › Forums › Public Support Forums › Help And Support › Washing Machine Help Forum › VT1014D23 – runs for 4 seconds at a thim

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • June 11, 2016 at 12:33 pm #88538
    abhaslaj
    Participant

    Hello,
    I hope someone can help me. Our Hoover VisionTech VT1014D23 (now out of warranty) was halfway through a wash cycle when it started to work erratically.

    It runs for about 4 seconds, then cuts out completely (the display goes blank) for the next 4 seconds, then it comes back to life and runs for another 4 seconds. It keeps up this switching on and off indefinitely.

    Could it be some kind of thermal cut out? There are no error codes displayed.

    June 11, 2016 at 3:05 pm #438482
    electrofix
    Moderator

    Re: VT1014D23 – runs for 4 seconds at a thim

    no sounds more like a board problem

    Dave

    June 11, 2016 at 4:49 pm #438483
    abhaslaj
    Participant

    Re: VT1014D23 – runs for 4 seconds at a thim

    Thanks Dave, is there just a single board in these machines? How can I confirm that is the fault?

    June 11, 2016 at 6:04 pm #438484
    electrofix
    Moderator

    Re: VT1014D23 – runs for 4 seconds at a thim

    difficult no easy way to be sure 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} but is sounds like the board power supply is acting up
    you could contact EMW electronics or http://www.qer.biz/servreps.htm
    and see if they can test and repair this board.
    another problem that we are getting these days is unprogrammed boards so if you buy a new one its useless unless you have the gear to programme it

    Dave

    June 12, 2016 at 9:54 am #438485
    abhaslaj
    Participant

    Re: VT1014D23 – runs for 4 seconds at a time

    I took the board out. Sadly there was no obvious problem, like a blown electrolytic, so I put it back together. Since reassembling, the machine no longer displays anything – it appears completely dead.

    I will contact QER as you suggest. I am a pessimistic, but it would be a terrible shame to scrap the whole machine for the sake of what is likely to be a single component.

    Thanks for your help

    June 12, 2016 at 10:37 am #438486
    admin
    Keymaster

    Re: VT1014D23 – runs for 4 seconds at a thim

    Hi

    Dependent on the product and serial number there is approx 6-8 different versions of board required on this machine.It maybe better to get a complete new board. will need the 16 digit number tho to confirm board.

    Bryan

    June 12, 2016 at 11:55 am #438487
    abhaslaj
    Participant

    Re: VT1014D23 – runs for 4 seconds at a thim

    Thanks Bryan.

    I found this:
    http://www.buyspares.co.uk/module-progr … =VT1014D23

    But sadly out of stock. As we now don’t have a working machine, I can’t take the risk of it taking weeks to be restocked.

    Any suggestions as to where else may have it?

    June 12, 2016 at 6:39 pm #438488
    admin
    Keymaster

    Re: VT1014D23 – runs for 4 seconds at a thim

    Hi

    How do you know that that one was the correct one.. As I have stated there are about 8 different ones dependent on the 16 digit product/serial number.You are not guaranteed the correct one without this information as they are different. We hold most of them in stock.

    Bryan

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.