- This topic has 12 replies, 3 voices, and was last updated 8 years, 9 months ago by
.
-
Posts
-
Hi, we get this error, E:42 when doing a hot wash, 60 degree wash.
40 degree washes are OK.Does anyone know what might be causing this error?
Thanks.
Phil. 🙂
Re: Bosch WAQ2830SGB washer E:42 error
Might be a motor fault check wiring to motor and carbon brushes on motor
Re: Bosch WAQ2830SGB washer E:42 error
Hi Dave thanks, yes looks like it is the motor, it now won’t complete any wash or even the rinse and spin.
Where might I buy the brushes?Phil
Re: Bosch WAQ2830SGB washer E:42 error
Hi Steve removed the brushes today they are not worn, I put them back and tried another wash and this time it worked 😀 I then tried a second wash and it failed with the same E42 error so doesn’t seem to be a bruushes or motor issue most strange, any ideas?
Thanks.
Phil.
Re: Bosch WAQ2830SGB washer E:42 error
Hi anyone else come across the E:42 issue before and knows what it is?
Thanks
Phil.
Re: Bosch WAQ2830SGB washer E:42 error
Hi I have another problem now, I replaced the motor and the E:42 error remained.
So I followed the reset recommended on this site, and now the motor won’t move at all, the machine fills with water and empties but the drum doesn’t turm at all so please please what has happened? did the reset wipe the program settings?
Need urgent help
Philip
anyone know how to do a reset on a WAQ283S0GB bosch machine?
Hi I’ve replaced the motor on my machine but the E:42 error remained, tried to do a reset and now the drum doesn’t turn at all.
Need help doing the reset for this machine.
Thanks
Phil
Re: Bosch WAQ2830SGB washer E:42 error
its not helpful to add a new post on the same thing so I have merged them
if your motor went before and will not now check
1 when you had the brush out did it go back properly. they have a habit of sticking before they contact the armature. my trick it to push them down with a cocktail stick and then you know it all the way. also check the brush wire is on
2 make sure the motor plug is in correctlyDave
Re: Bosch WAQ2830SGB washer E:42 error
Hi Dave thanks for the reply the issue isn’t with the brushes, I have tried a reset and this appears to have messed up the programming, do you know how to do a reset on this model?
How can I check if the reset was successful?Thanks
Phil.
Re: Bosch WAQ2830SGB washer E:42 error
cant see model. can find WAQ283S0gb is that yours ?
common reset that does a lot of bosch
turn to 6 o clock
press and hold spin speed button
turn to 7 o clock
now release spinwait about 2 secs between each step ie don’t be too quick
Dave
Re: Bosch WAQ2830SGB washer E:42 error
OK further news, most odd have obtained information on how to do a test program.
Completed that after doing the reset, everything passed fine.
Tried a wash at 40 degrees, the mixed load, and the E42 error came back, noticed something very odd though.
I’ve noticed that when the motor tries to turn the drum it seems to surge, it seems the power is on maximum there’s no gentle thrust. Sometimes its so violent the drum casing hits the side of the machine with a bang, and on odd occasions the right hand side of the machine actually lifts off the floor.Surely this cannot be correct, then after a few attempts at turning the drum in the wash cycle, the E42 error occurs.
This isn’t correct, the machine never did that before, any idea what could be causeing the machine motor to do this? I’ve replaced the motor with another so I can’t see it would be the motor.
I checked the drum turning by hand when the machine is empty and from inside the machine turning by hand the drum turns freely so it’s not the bearing locking up.
Loosing patience and running out of ideas.
Phil
- You must be logged in to reply to this topic.