Dear iadom (HPT WF…)

[Goatboy]

leavemetogetonwithit wrote:HOTPOINT washing machines stuck in “test” mode late models e.g. WF630G with display on fascia.
This is caused when user accidentally pushes on/off and start buttons simultaneously.
To exit test mode press start again > display goes wild>press start again>display settles down >
then press on/off plus start buttons simultaneously and hold for few seconds till display reads “D:end” or “D:off” or similar.
Machine should now function normally.

Yet to be learned how to conduct test mode.

I’m going to one of these this afternoon 😕

Anyone know anything about the test procedure yet?

[maltheviking]

Re: Dear iadom (HPT WF…)

Have a look at this thread

Hotpoint/Indesit TEST BLOCK

Three phase motor on this begger, WATCH OUT for the big heatsink on the power board DO NOT TOUCH IT for five minutes after mains disconection or it will kick.

SERVICE MANUAL 5407104

Mal

[iadom]

Re: Dear iadom (HPT WF…)

Sadly true, I think I will muddle along without the £130 + vat hardware key. The display does give error codes so I will manage with that for the moment. 😥

[Goatboy]

Re: Dear iadom (HPT WF…)

maltheviking wrote:WATCH OUT for the big heatsink on the power board DO NOT TOUCH IT for five minutes after mains disconection or it will kick.

I’m worried about the DIYers at home! 😯

Anyhoo, twas just in test mode, cheers Mike! :tup:

[leavemetogetonwithit]

Re: Dear iadom (HPT WF…)

Goatboy wrote:

I’m worried about the DIYers at home! 😯

Anyhoo, twas just in test mode, cheers Mike! :tup:

‘Twas Iadom who helped me with this info last year and I just put it in error codes.
Was lucky not to get a belt meself as the module was the first thing I looked at that day. One of the advantages of being slow; probably the thing had discharged itself by the time I got to it. 😀
Mike

[Pigpen4]

Re: Dear iadom (HPT WF…)

maltheviking wrote:
Three phase motor on this begger, WATCH OUT for the big heatsink on the power board DO NOT TOUCH IT for five minutes after mains disconection or it will kick.

SERVICE MANUAL 5407104

Mal

I’m not sure how to obtain this Service Manual – I’m looking for the meter readings that I should be expecting from a Hotpoint 3-phase motor.
Can anybody help, please?

Many thanks,
Pigpen.

[RocketMan]

Re: Dear iadom (HPT WF…)

I can but not until later tomorrow. Got the manual in the garage (saw it today) but busy all day until late. Unless some one comes up before…

Steve

[iadom]

Re: Dear iadom (HPT WF…)

Sorry, should have said, I sent a copy last night. 😉

[Pigpen4]

Re: Dear iadom (HPT WF…)

Thanks, Jim. 😉

[shaun67]

Re: Dear iadom (HPT WF…)

Hi ladom,

Any chance you could send me a copy please 🙂

Shaun

[shaun67]

Re: Dear iadom (HPT WF…)

Thanks Jim :tleft:

Shaun

[allan73]

Re: Dear iadom (HPT WF…)

Any chance I could have a copy also Jim ?

Allan.

[allan73]

Re: Dear iadom (HPT WF…)

Cheers Jim, :worthy:

[pup]

Re: Dear iadom (HPT WF…)

Hi ladom,

Any chance you could send me a copy please 🙂

thanks umed

[Pigpen4]

Re: Dear iadom (HPT WF…)

Check your emails, Umed.
Pigpen. 😉

[Author]

Posts