Pat Test Failure Whirlpool ADP4501/5

Home Forums Trade Technical & Spare Parts Forums Trade Technical Enquiries Pat Test Failure Whirlpool ADP4501/5

Viewing 11 posts - 16 through 26 (of 26 total)
  • Author
    Posts
  • #303552
    mike412
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    Hi Folks.

    My “case” turned out slightly different. On reading the instruction card for the pat test it seems that the parameters are set too low, ie the “Touch Tester” pass was set at 1.0ma, far too low.
    This pat tester can be pre programmed but it needs an access code that the site manager does not have, nor does he have the authority to change the settings.
    I will be writing to the school to advise them to consult a member of the IEE for advice. Suffolk County Council should have one of them behind a desk somewhere.

    Thanks for all your Help folks.

    Regards,

    Mike

    #303553
    Specialist01269
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    Hi Mike: Makes you wonder if the Site Manager actually went on a PAT testing course or was he Just given a PAT tester with pre-set parameters & told to rely on it’s results.
    I’ve seen this quite a few times with local authorities & Big business, 1 person is the designated tester but often has no actual experience just relies on the pass fail indication given & the results printed out.

    At least you got to the bottom of it in the end.

    Andy

    #303554
    mike412
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    Hi Andy,

    I was very impressed with the Knowledge and attitude of the site manager, who had gleaned much from his one day course at the local technical college.

    He is a conscientious chap, doing his job correctly, unfortunately with incorrect kit.

    Thanks once again ,

    Mike

    #303555
    bazza500
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    Well, the saga continues….

    Got 2 new mains filter units and gave them to the electrician to test before fitting them to the machine and he failed them both although I had insulation tested them and found them >999Mohms. He is again, failing them on 3.9ma.

    Does anyone have anything official, in writing, that says this test is not compulsory?

    #303556
    garn
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    Theres A Mega Roadshow Traveling The Country Its A Free Day Out With Refrshments 🙂 It May Be Worth A Visit Somebody may Learn Something Or Even Buy One :rolls:
    Not Sure Where It is At The Moment But It In My Neck Of The Woods (wales) next Month For A Week.

    Garn….

    #303557
    don
    Moderator

    Re: Pat Test Failure Whirlpool ADP4501/5

    Hi garn

    If you happen to come across this roadshow could you get some contact details, venue locations or even better a web address. I`m sure if people knew about it they would support it especially if it means free refreshments.

    Don

    #303558
    garn
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    don wrote:Hi garn

    If you happen to come across this roadshow could you get some contact details, venue locations or even better a web address. I`m sure if people knew about it they would support it especially if it means free refreshments.

    Don

    give me A Couple Of Hours 😉

    paul…

    #303559
    garn
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    garn wrote:

    don wrote:
    Hi garn

    If you happen to come across this roadshow could you get some contact details, venue locations or even better a web address. I`m sure if people knew about it they would support it especially if it means free refreshments.

    Don

    give me A Couple Of Hours 😉

    paul… Check Your Have Mail 😉

    #303560
    don
    Moderator

    Re: Pat Test Failure Whirlpool ADP4501/5

    Megger roadshows as per the link here not quite what I was expecting but it may help someone.

    Thanks to garn for the info.

    Don

    #303561

    Re: Pat Test Failure Whirlpool ADP4501/5

    Interesting. There are a few “calibration days” mostly at electrical wholesalers’ premises. Most of the events though are “Money Talks – Megger shows how electricians can make more money” hosted at various golf clubs around the country. So that’s what it’s really all about. Wonder if Simon from Gosport has booked his place?
    Mike.

    #303562
    garn
    Participant

    Re: Pat Test Failure Whirlpool ADP4501/5

    sorry to disappoint you don. I was Hoping To Score Some Brownie Points Hear :wink:. I cant Find The Original Invitation The Cleaner Has Organized My Desk 🙁 So I Used The Webbsite.

    But Me And My Partner Cant Be The Only Business in GB That’s Been Invited To This Megger RoadShow With Free Breakfast And Refreshments 😀 There’s Got To Be More Info Somewhere.

    IL Let Everyone Know How It Goes IL be Attending The PembrokeShire Show As Long I Don’t Get Food Poisoning 😆

    Garn..

Viewing 11 posts - 16 through 26 (of 26 total)
  • You must be logged in to reply to this topic.