- This topic has 22 replies, 10 voices, and was last updated 20 years, 8 months ago by
.
-
Posts
-
I’ve been advised by a couple of local repairers that it’s not economical to replace the bearings on my Zanussi FL1085. They both estimated the job would take over three hours, which would certainly make that true.
However, a number of posts in the forums here suggest that, while the job does involve a lot of dismantling, a repairer with the right experience can expect to complete it in a little over an hour, which probably would make the repair worthwhile.
Is this true? If so, can anyone recommend a repairer in the Cambridge area who might undertake the work? (The ‘Repairs’ facility doesn’t provide any matches, unfortunately.)
Many thanks!
Re: Zanussi FL1085 bearings not worth repairing?
Postcode area is CB4. Thanks for the offer of help!
—
DaveRe: Zanussi FL1085 bearings not worth repairing?
I’d say it’s a 2 hour job.
Maybe 1 if your fast and had two pairs of hands. But fast makes mistakes.
I always recommend getting that repair done, as I like the Zanussi machine, and that is one of the only things that goes wrong with them.
Re: Zanussi FL1085 bearings not worth repairing?
Thanks for the info, Goatboy.
Yes, the machine’s given perfect service until now (it’s probably done somewhere around 1000 washes) so it was my feeling too that it was too early to just consign it to the tip.
I stopped using it as soon as free play became evident in the drum, so I’m hoping the damage is limited to the bearings.
Now I just need to find someone who thinks it’s an hour (or even two) job who’s prepared to do it!
—
DaveRe: Zanussi FL1085 bearings not worth repairing?
From the directories for you Dave 🙂
ONE CALL APPLIANCE CARE
16 Florence Walk
Dereham
Norfolk
NR19 1XG
Repairs to all makes and models
Same day / next day service
Covering NR PE IP CB1-CB11 Postcode areas
Tel. 01362 851792
Mobile. 07780885619
Email appliancerepairman@fsmail.netDave.
Re: Zanussi FL1085 bearings not worth repairing?
That’s miles away! But it does say CB4, so they must be prepared to travel. I’ll give them a call.
Cheers Dave!
—
DaveRe: Zanussi FL1085 bearings not worth repairing?
Had Tony from One Call round this morning to replace the bearings – how’s about that for fast service – and machine is now running perfectly again, so thanks to all.
For the record, it took about an hour and three-quarters, but at a reasonable price, so I’m happy. Just don’t lend him any sockets! (Sorry Tony!) 🙂
—
DaveRe: Zanussi FL1085 bearings not worth repairing?
I think I have the same issue bearing gone on a Zanussi FL1085.
Funnily enough I live in Naarfolk…
BUT – can’t get through to the 1st Call company and looked in yellow pages and they aren’t in there. – so are they still going ?
Can anybody recommend anybody else in the Norfolk area to repair my washer machine.
HOw much should I expect to pay to get it fixed if it is the bearings ?Re: Zanussi FL1085 bearings not worth repairing?
woollyjumper wrote:How much should I expect to pay to get it fixed if it is the bearings ?
£90 -£120?
Rates vary massively. You’ll need the drum support too if the barings are being changed.
woollyjumper wrote:Can anybody recommend anybody else in the Norfolk area to repair my washer machine.
Dave, the expert of such things, is on holiday this week 8) Maybe Kenny will see this and help you out? But something tells me, he’s abit busy 😕
Re: Zanussi FL1085 bearings not worth repairing?
Thanks Tony
has rang me back this morning and is coming out on Monday evening.So hopefully it be the £120 – or its off buy a new one 😥
Re: Zanussi FL1085 bearings not worth repairing?
Hi,
I have the same fault with drum ballbearings on my Zanussi FL1084. Is it economically worth calling an engineer?
Thanks,
Teasy 🙄Re: Zanussi FL1085 bearings not worth repairing?
It is a very involved process with tank having to be extracted form chassis.
Try the engineer link below for help.Greg
Re: Zanussi FL1085 bearings not worth repairing?
I let you know on Monday after he has been !
Either £120 to repair or over £400 for a decent new one.
I’d rather stick with one that has worked well…
- You must be logged in to reply to this topic.