aeg kdwi d/w

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › aeg kdwi d/w

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • October 28, 2005 at 10:15 pm #12900
    eng14
    Participant

    went to this d/w 3 weeks ago,cleared out system.started to fill again worked fine then stopped filling again.went to zanussi at maidenhead my mates there told me its ovrfilling and need a conversion kit,which is new valves wiring,tubes etc,is there anyway to repair this without kit as it has worked fine for 5 years they say its overfilling and this will cure it ta for any advice richard.

    October 28, 2005 at 11:30 pm #152179
    Dave_Conway
    Participant

    Re: aeg kdwi d/w

    Fit the IWMS conversion kit 😉

    It solves so many problems 😀

    Dave.

    October 29, 2005 at 7:09 am #152180
    bobokines
    Participant

    Re: aeg kdwi d/w

    What exactly is this kit and why is it needed? I have seen loads of Zan dishwashers with blockages but I have never been unable to sort them out. Surely the time taken to fit the kit would be the same as to clean out the old one. Or am I missing something?

    Bob

    October 29, 2005 at 9:42 am #152181
    Dave_Conway
    Participant

    Re: aeg kdwi d/w

    It consists of a new air break, pressure switch, inlet valve etc basically everything to resolve the intermittent no fill problems with these.

    But yes, cleaning them does work quite often.

    Dave.

    October 29, 2005 at 5:46 pm #152182
    bobokines
    Participant

    Re: aeg kdwi d/w

    Is it “One kit fits all”? or are a there several kits. If it is a universal, do you have a part number please.

    Thanks
    Bob

    October 29, 2005 at 6:41 pm #152183
    iadom
    Moderator

    Re: aeg kdwi d/w

    Not sure about all Zanussi models but I had one last week that I cured by cleaning out the gunge, however checking on TDS on this one model reveals two different kits, one for the “New Structure” & one for the “Evolution” type machines, you can tell which is which by looking in the sump/base.

    Model was a DWS909

    October 29, 2005 at 6:44 pm #152184
    iadom
    Moderator

    Re: aeg kdwi d/w

    Dave_Conway wrote:Fit the IWMS conversion kit 😉

    It solves so many problems 😀

    Dave.
    Is this what TDS info calls “The new ATB system” ?

    October 29, 2005 at 8:05 pm #152185
    Dave_Conway
    Participant

    Re: aeg kdwi d/w

    I’m not sure about the “ATB System” to be honest, but I would imagine it’s the same thing. Normally the diagram shows a large bracket enompassing all the above parts.

    There are a few variations as well, PNC is always required to get the right kit.

    Dave.

    October 29, 2005 at 8:40 pm #152186
    bobokines
    Participant

    Re: aeg kdwi d/w

    I like to complete as many calls as I can on the first visit. If there is not a universal kit and cleaning it out clears the problem, then how is it viable to make an incomplete call just to go back with go back with a special kit?

    :con:

    Bob

    October 29, 2005 at 8:58 pm #152187
    Dave_Conway
    Participant

    Re: aeg kdwi d/w

    From experience, I would go once and attempt the clean out job, if it happens again fit the kit on the recall visit 🙂

    Dave.

    October 29, 2005 at 9:33 pm #152188
    bobokines
    Participant

    Re: aeg kdwi d/w

    OK… Are the part numbers available on the TDS disk or do I keep guessing???


    😉


    Bob

    October 29, 2005 at 9:43 pm #152189
    Dave_Conway
    Participant

    Re: aeg kdwi d/w

    On the TDS disk Bob, or they should be.

    If not, let me know and I’ll check with Lux directly, I’ll need the PNC though 🙂

    Dave.

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.