ZAN FJS1225W 914512720/00

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › ZAN FJS1225W 914512720/00

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • November 14, 2005 at 6:47 pm #13292
    DAR01
    Participant

    Customer washed bath mat ,OOPS (which broke up in machine).

    Cleared residue out of drum,pipes and expansion chamber.
    Machine fills with water, then motor goes into a partial spin.

    Checked motor/tacho seems OK.

    Last test reset to drain programme stopped on 1 minute,couldn’t open door.

    Any ideas anyone?

    😕 😕 😕

    Mike

    November 15, 2005 at 12:36 am #154059
    leavemetogetonwithit
    Participant

    Re: ZAN FJS1225W 914512720/00

    DAR01 wrote: ,couldn’t open door.
    Mike

    Is it one of those locks with a tube on? ➡ pressure sw chamber still has bit of bath mat in ❓

    November 15, 2005 at 1:47 pm #154060
    DAR01
    Participant

    Re: ZAN FJS1225W 914512720/00

    Newer type door sw no pipe.

    November 15, 2005 at 1:57 pm #154061
    DAR01
    Participant

    Re: ZAN FJS1225W 914512720/00

    Anyone know how to configure the Zan Module ,please.

    MIKE

    November 15, 2005 at 2:09 pm #154062
    mbdas
    Participant

    Re: ZAN FJS1225W 914512720/00

    Did the drain pump run ❓ I think it has a TOC in it poss more bath mat in it .Have you had the pcb out if so can you see if anything is blown on it
    I’ve had a few where the drain or recirculation pump has shorted and then blown the pcb.
    mark

    November 15, 2005 at 4:49 pm #154063
    fennyapps
    Participant

    Re: ZAN FJS1225W 914512720/00

    If you have TDS offline all the information is listed after you type in PNC no: at the bottom of screen. Diagnosis, configuration etc.

    Hope this helps
    Paul

    November 15, 2005 at 9:22 pm #154064
    DAR01
    Participant

    Re: ZAN FJS1225W 914512720/00

    No obvious damage to board, pumps out OK

    Mike

    November 15, 2005 at 10:36 pm #154065
    Dave_Conway
    Participant

    Re: ZAN FJS1225W 914512720/00

    Mike, if you’re on Broadband i can send a hefty 1.5mb pdf I have if it may help ?

    Dave.

    November 16, 2005 at 1:00 am #154066
    leavemetogetonwithit
    Participant

    Re: ZAN FJS1225W 914512720/00

    DAR01 wrote:Machine fills with water, then motor goes into a partial spin.

    (This shouts tacho,doesn’t it?)

    (Even though.)

    tacho seems OK.


    Mike

    Edit 8.30am: Suggest wiggle all wiring between tacho and pcb then check again for correct resistance from where it joins timer. Most likely place is motor connector but could even be connection inside motor plug. (Trying to spin with water in could have stressed connections).

    November 16, 2005 at 1:41 pm #154067
    DAR01
    Participant

    Re: ZAN FJS1225W 914512720/00

    Got TDS now goig to customer this afternoon armed with a thick file and a deck chair.

    Thanks for all the info.

    MIKE

    November 21, 2005 at 1:54 am #154068
    DAR01
    Participant

    Re: ZAN FJS1225W 914512720/00

    Replaced module ,working OK.

    Mike

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.