hotpoint dwf61p – circulation pump slow

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › hotpoint dwf61p – circulation pump slow

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • June 19, 2006 at 3:33 pm #18573
    stuffed
    Participant

    circulation pump seems to me to be slow, its not pumping much water through the rotating arms, ive checked
    filters clean
    water feed hose clean
    can rotate pump by hand
    i read about running on the starting windings in one of the posts, how can you tell if this is so.

    June 19, 2006 at 6:15 pm #179483
    Martin
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    It’s more likely a water starvation/circulation problem and not a motor problem. If you fail to use salt in hard water area then that can cause problems with the instanteneous water heater and its control valve.

    Time for expert intervention I would suggest (Click on link below) 😉

    June 24, 2006 at 10:09 am #179484
    stuffed
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    stripped pump down and checked motor- thats ok , however white seven bladed rotor is very worn, with no points to physically connect it to blue plastic drive- can i get just this rotor

    June 24, 2006 at 10:55 am #179485
    Dave_Conway
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    stuffed wrote:can i get just this rotor

    Yep, you can 🙂

    I’ll need the serial number to identify though as there were two different circulation motors used on this model.

    Dave.

    June 24, 2006 at 12:51 pm #179486
    stuffed
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    the no on motor is 5600.031929 / isol.kl.f / mo1757/230-240v does that look right

    June 24, 2006 at 2:25 pm #179487
    Penguin45
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    Dave will need the one from the rating plate of the appliance, not the motor code.

    Regards,
    Penguin45.

    June 24, 2006 at 5:53 pm #179488
    stuffed
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    nos i have are
    dwf61p/07
    79700434
    fd80093023type 59e71h
    1000710220898390233

    June 25, 2006 at 7:01 am #179489
    Martin
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    1801737 is the part number for a replacement Impellor Kit in this case 😉

    June 25, 2006 at 9:11 am #179490
    Dave_Conway
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    Blimey, not cheap is it 😯

    £44.38 ex VAT and carriage, an email to spares@ukwhitegoods.co.uk please if required 🙂

    Dave.

    June 28, 2006 at 7:45 pm #179491
    stuffed
    Participant

    Re: hotpoint dwf61p – circulation pump slow

    holding fire on the impellor for the moment,
    as I have already rebuilt existing – it basically a domestic heating pump impellor. only meant to be temporary job tho, and all is nearly fine except timing as shown on display . originally after fault whatever program selected – it said ( apart from cold prewash) 2hrs to go. now quick wash says 29 mins to go ( as it used to before fault), is the machine clever, ie is it learning as it goes .

    PS as a heating engineer i have to take boilers and sometimes houses apart to fit things and its a damm site easier than this – my hats off to you if you do it for a living

  • Author
    Posts
Viewing 10 posts - 1 through 10 (of 10 total)
  • You must be logged in to reply to this topic.