Hotpoint CTD80 condensing tumble dryer

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Hotpoint CTD80 condensing tumble dryer

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • October 12, 2006 at 3:16 pm #21637
    Bernie
    Participant

    Just been to a Hotpoint CTD80 condensing tumble dryer, serial 509220336 customer has fitted a thermostat kit to it him self.
    only he’s not sure he fitted them correctly as it still don’t work.

    F13 Rear NTC open or short circuit

    I have just read on this site that the kit 1703607 that he used has three stats in it, when I had a look I could only see just the two above the heater.
    He did show me the old ones and the one shot had gone and there was only two in the box.

    What I need to know is which stats go where and how to identify which ones which.
    I know one is a white dot and its been fitted on the left as you look at it, which I believe is correct.

    Bernie

    October 12, 2006 at 4:35 pm #191966
    iadom
    Moderator

    Re: Hotpoint CTD80 condensing tumble dryer

    I can send you a wiring diagram if you like. Personally, I would run a mile from this, I am wondering what the punter has done with the wires to the missing stat or ntc. 😯

    Jim.

    October 12, 2006 at 4:47 pm #191967
    Bernie
    Participant

    Re: Hotpoint CTD80 condensing tumble dryer

    Thank you for the offer of a wiring diagram that would be good.
    I like to help people if I can and I am intrigued with this one
    I know I’am mad!

    Bernie

    October 12, 2006 at 4:48 pm #191968
    iadom
    Moderator

    Re: Hotpoint CTD80 condensing tumble dryer

    Will sort it later, time to make the tea now, 8)
    Jim.

    October 12, 2006 at 7:37 pm #191969
    SDR
    Participant

    Re: Hotpoint CTD80 condensing tumble dryer

    before date code 50712 which yours is the heater only has 2 stats one shot and cycling, after dc 50712 they used 3 stats. by the sound of it you will need to fit a module and eeprom. one thing though check condenser these block within about 2 weeks on this piece of sh, sorry i mean this little baby 😆 let me know if need any more info as i franchise for hotpoint, got up to date partfinder.

    October 12, 2006 at 7:42 pm #191970
    SDR
    Participant

    Re: Hotpoint CTD80 condensing tumble dryer

    sorry got that wrong from dc 507120000 jul 05 the cycling stat was removed . 😳

    October 12, 2006 at 7:44 pm #191971
    iadom
    Moderator

    Re: Hotpoint CTD80 condensing tumble dryer

    Thanks for that info SDR, absolutely no mention of two stats on the latest, trade version of Partfinder that I can see, no mention of it in manual 5412719 either. 😥

    Jim.

    EDIT, just seen your last post. Partfinder still lists two different, 3 stat kits. One before date code 51130, 28/11/05 as a 1603607 and after that date a 1603608. Now I am confused. 😕 😥

    October 12, 2006 at 8:01 pm #191972
    SDR
    Participant

    Re: Hotpoint CTD80 condensing tumble dryer

    just had another look on partfinder, there is a red tec bulletin on this dryer , if a heater vwith 2 stats fitted on appliance it must be replaced with a heater kit 1703245 from ser no 507120001 to 511299999 (29/11/2005) or a 1703595 from ser 511300001 (30/11/2005) to date. heater kit comes with stats fitted. hopes this makes sense. thing is if stats are ok that cust fitted it will still be module needed.

    October 12, 2006 at 10:04 pm #191973
    iadom
    Moderator

    Re: Hotpoint CTD80 condensing tumble dryer

    Thanks for making that clear, I think. 😀

    Much appreciated.

    Jim.

    October 14, 2006 at 3:34 pm #191974
    Bernie
    Participant

    Re: Hotpoint CTD80 condensing tumble dryer

    Thanks for all the information and thanks to Jim for the wiring diagram.
    Going back to it on monday 16th Oct will let you know how I get on.

    Bernie

  • Author
    Posts
Viewing 10 posts - 1 through 10 (of 10 total)
  • You must be logged in to reply to this topic.