Siemens WM71631/01 no drum action

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Siemens WM71631/01 no drum action

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • November 11, 2006 at 4:03 pm #22468
    admin
    Keymaster

    WM71631/01 FD7309 Seriel00653 has no drum action and neither door cannot open from button. If I select for washing indicate the door locked and start to fill water and further nothing… No error…
    If select spining program also starts to pump out and also no drum action and neither error… at the end of program cannot open door from button.
    Advice?

    November 11, 2006 at 4:36 pm #195087
    gegsy
    Participant

    Re: Siemens IQ716 no drum action

    Hi Baron
    The door lock may think it still has a certain amount of water left in the drum. You could drain appliance down at filter and then try again. The same goes for the spin cycle also, ie certain level of water detected- No spin.
    PS – This has a manual door unlock behind filter door just like the Miele 😉

    Greg

    November 11, 2006 at 4:43 pm #195088
    admin
    Keymaster

    I know but it is no water inside now… It has one “water sensor” on one tube and also overflow sensor. I have tried with that sensor dismantled from his case, to get in spin cycle but nothing…

    November 11, 2006 at 5:03 pm #195089
    gegsy
    Participant

    Re: Siemens IQ716 no drum action

    Ok assuming brushes and motor check out ok, then I would be looking personally towards interlock or module fault, as you have checked the pressure system already 😉

    Greg

    November 11, 2006 at 5:07 pm #195090
    gegsy
    Participant

    Re: Siemens IQ716 no drum action

    Baron……….Check your email 😉

    Greg

    November 11, 2006 at 7:27 pm #195091
    admin
    Keymaster

    Re: Siemens WM71631/01 no drum action

    Thanks Greg, :tup:
    Excuse for delay but I was gone from home.
    I will check all on Monday.

    P.S. You’ve assumed right that I’ve checked pressure system and door lock. 8)

    November 11, 2006 at 7:30 pm #195092
    gegsy
    Participant

    Re: Siemens WM71631/01 no drum action

    baron wrote:P.S. You’ve assumed right that I’ve checked pressure system and door lock. 8)

    Of course your an engineer 😆

    Greg

    November 11, 2006 at 7:45 pm #195093
    admin
    Keymaster

    Re: Siemens WM71631/01 no drum action

    Greg :beer: :beer: :beer: :pirate:

    November 11, 2006 at 8:31 pm #195094
    gegsy
    Participant

    Re: Siemens WM71631/01 no drum action

    Now you talkin, and I reckon you owe me a few pints 😆

    Greg

    November 11, 2006 at 9:01 pm #195095
    timdowning
    Participant

    Re: Siemens WM71631/01 no drum action

    Had low insulation on heaters hold door locks on, may be worth eliminating first before ordering modules!!!

    November 14, 2006 at 5:33 pm #195096
    admin
    Keymaster

    Re: Siemens WM71631/01 no drum action

    Greg, I have tested today.
    After entering in test program, first it shows F10. I have set it for motor test and it worked without any error. It is already in third probe and goes OK. 8)

    I didn’t find anything wrong before getting into test.
    Please, what means F10 (I don’t have error list for this machine). :bounce:

    Thanks 8)

    November 14, 2006 at 5:41 pm #195097
    gegsy
    Participant

    Re: Siemens WM71631/01 no drum action

    Hi Baron
    F10 is no communication between power module and motor control PCB.

    Either faulty PCB/s or loom connection fault.

    Greg

    November 14, 2006 at 6:13 pm #195098
    admin
    Keymaster

    NICEEEE….
    I can not explain how it’s possible to repair or remove one problem without doing anything, only getting into test (without touching any cable or module).

    Thanks’ again GREG…

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)
  • You must be logged in to reply to this topic.