zan TD dead

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › zan TD dead

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • June 20, 2007 at 10:26 am #28300
    abbots
    Participant

    TCE7276W.

    hi guys,
    power supply ok,door switch ok.
    the lights on the front come on but no motor action or heat or anything.
    are the PCB’s problematic on this model?
    is there something i’m missing here?
    thanks,
    john

    June 20, 2007 at 11:16 am #217738
    Martin
    Participant

    Re: zan TD dead

    abbots wrote:is there something i’m missing here?

    Have you checked the safety switch on the condenser access panel?

    ….or the T/stat in the front drum housing?

    June 20, 2007 at 12:23 pm #217739
    abbots
    Participant

    Re: zan TD dead

    no i haven’t were are they situated?
    john

    June 20, 2007 at 12:27 pm #217740
    Martin
    Participant

    Re: zan TD dead

    abbots wrote:no i haven’t were are they situated?
    john

    Please read my post again as I have told you where they are 😉

    June 20, 2007 at 12:31 pm #217741
    abbots
    Participant

    Re: zan TD dead

    oh very very sorry martin,
    just didn’t quite ubder satand what you meant by access panel thats all
    jk

    June 20, 2007 at 1:51 pm #217742
    abbots
    Participant

    Re: zan TD dead

    the microswitch behind the bottom right hand side of the plinth that indicates when the condensor flap is open is fine.
    i cant seem to see a t/stat on the front of the drum,i cant see one listed on connections either,only a NTC temperature probe,will this be in the same place as the thermostat on the older condensor dryers i.e. near the top of the drum front.
    If so how do you get to it to test it?when the lid is removed all you can see is a white plastic housing and the PCB cover.
    does the front of the machine come off or do you have to remove the drum from the rear?
    even the control panel seems a nightmare to get off, is there an easy way.?
    when you swith the machine on all that happens is the “time to go” is dislayed and the start light flashes as if it’s ready to go ,but nothing happens when the start button is pressed,is there a matrix behind the switch that breaks, so the button doesn’t make contact with the switch?
    any advise will be great.
    thanks
    john

    June 20, 2007 at 2:06 pm #217743
    ANDYVIVO
    Participant

    Re: zan TD dead

    Hi John
    It will be a broken “light diffuser” which is a frame for the buttons and lights, VERY common part. Correct PNC will get you the right one!
    Regards Andy

    June 20, 2007 at 2:09 pm #217744
    abbots
    Participant

    Re: zan TD dead

    nice one Andy,

    never heard of the part.
    TCE7276W
    916092667/00
    Sn 43400181

    part number would be great

    where is the part situated and how do i get to it?
    thanks buddy.
    john

    June 20, 2007 at 3:25 pm #217745
    ANDYVIVO
    Participant

    Re: zan TD dead

    Hi John,
    It is part number 1251185300 in stock @ Masterpart £4.20 +.
    Located between the fascia panel and module, (it makes contact from the yellow button to the module), fascia off, then remove module WITH housing and all will be revealed. 😉
    Regards Andy

    June 20, 2007 at 3:30 pm #217746
    abbots
    Participant

    Re: zan TD dead

    cheers andy

    June 20, 2007 at 3:32 pm #217747
    wilf
    Participant

    Re: zan TD dead

    yep light diffuser every time

    wilf

    June 20, 2007 at 4:48 pm #217748
    cab
    Participant

    Re: zan TD dead

    did one today, common as .

    cab

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.