Hotpoint WD61P 185 deg Dryer Stat.

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Hotpoint WD61P 185 deg Dryer Stat.

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • June 29, 2007 at 7:08 pm #28593
    Turbo
    Participant

    Can someone help me on this one please.
    Went to fit new one shot stat to this machine today (1605635) but although is was the correct temp rating it was physically larger than the one it was to replace and would not fit.
    Any help would be good thanks.
    Turbo.

    June 29, 2007 at 7:13 pm #219052
    Penguin45
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Cut-out is 1600870.

    Chris.

    June 29, 2007 at 8:05 pm #219053
    admin
    Keymaster

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Hi

    Also check the fan is running correctly and that there is no fluff build up

    Bryan

    June 29, 2007 at 8:09 pm #219054
    Turbo
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Thanks Chris, just tried putting that number in to Connect system and it comes up 1605635 again but I am sure you are right having looked at a picture in the Parts Centre Cat, will ring the Rep and tell them to sort it out.

    June 29, 2007 at 8:12 pm #219055
    Turbo
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Thanks Bryan blowing a gale down the old chimney 😆

    June 29, 2007 at 8:28 pm #219056
    Bryan
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    From memory the last time I did one of them , there was a modification leaflet instructing you to bend the metal bracket slightly in order to accomodate the new thermostat.

    HTH

    Bryan

    June 29, 2007 at 8:46 pm #219057
    Turbo
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Thanks may have to go back and have another look.

    June 29, 2007 at 9:46 pm #219058
    Bryan
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    In fact Turbo , here’s Martin with his camera.

    Bryan

    June 29, 2007 at 9:47 pm #219059
    iadom
    Moderator

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Bryan is correct, this replacement stat needs the bracket bending back to fit, there should have been a leaflet with the new stat.

    Nice link Bryan, hadn’t seen that post from Martin.
    8)
    Jim.

    June 29, 2007 at 9:54 pm #219060
    Bryan
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Just thought I’d credit Martin so he didn’t see it as a bit of plagiarism 😉 🙂

    Bryan

    July 1, 2007 at 10:32 am #219061
    bobokines
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Don’t miss the reason for the stat failing. Normallly it’s due to an earth fault on the harness by the motor. The orange wire IIRC

    Bob

    July 1, 2007 at 6:02 pm #219062
    iadom
    Moderator

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Seen more fail due to broken wire to fan motor. The one you mention Bob is common with FHP motor.

    Jim.

    July 1, 2007 at 6:34 pm #219063
    Bryan
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Turbo wrote:blowing a gale down the old chimney 😆

    I presume this meant there was no problem with the fan :).

    Bryan

    July 2, 2007 at 6:55 pm #219064
    Turbo
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Thanks for all your help on this one guys, new stat now in place after a bit of work with the pliers. Found 2 broken wires near the motor plug which I have fixed.
    Thanks again


    Graham

  • Author
    Posts
Viewing 14 posts - 1 through 14 (of 14 total)
  • You must be logged in to reply to this topic.