hoover dryer dead

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › hoover dryer dead

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • October 26, 2007 at 3:23 pm #31716
    abbots
    Participant

    hi,
    HNC160-80
    31100067

    this dryer is completely dead except for the red “on” light when start is pressed.
    door interlock OK, supply OK, front red spot stat OK, had the drum out to check wiring and float switch, all seems OK.
    Is there something i’ve missed or is it the timer maybe?
    if so has any one a part number for it?
    thanks.
    john

    October 26, 2007 at 3:32 pm #232263
    Martin
    Participant

    Re: hoover dryer dead

    I can send you the wiring diagram if that will help? 😉

    October 26, 2007 at 3:35 pm #232264
    timdowning
    Participant

    Re: hoover dryer dead

    Has this dryer got a display board on it with a triangular neon under the word start?

    If it has then the on light comes on when the on/off button is pushed in. The triangular start neon should then flash until you press start.

    If the on light is on but the triangular start neon dosen’t flash then I would assume the pcb is at fault.

    Hope i’ve got the right model. 😕

    October 26, 2007 at 3:41 pm #232265
    timdowning
    Participant

    Re: hoover dryer dead

    p.s

    If its not the model I said… it might be just the start pcb as on the previous range.

    October 26, 2007 at 4:04 pm #232266
    abbots
    Participant

    Re: hoover dryer dead

    if it’s the start relay why haven’t i got power to the heater?and i would have thought by keeping the on switch pushed in i would have got motor action untill i released the button.
    john

    October 26, 2007 at 4:12 pm #232267
    timdowning
    Participant

    Re: hoover dryer dead

    and i would have thought by keeping the on switch pushed in i would have got motor action untill i released the button

    On this model is it turn timer dial and press start?

    Or is it turn timer dial, switch on/off switch on, and then press start?

    October 26, 2007 at 7:15 pm #232268
    Penguin45
    Participant

    Re: hoover dryer dead

    It has got the little start run PCB on board. If it won’t do anything at all, you’ve probably lost a neutral somewhere. Down the front near the pulley wheels is a good bet, or yes, perhaps the timer.

    Chris.

    October 27, 2007 at 8:25 am #232269
    Martin
    Participant

    Re: hoover dryer dead

    abbots wrote: i would have thought by keeping the on switch pushed in i would have got motor action untill i released the button.

    That’s correct John, holding the start button in the motor would turn and at least you would hear the timer motor turning!

    Do you want these wiring diagrams I have or what? 😉

    October 28, 2007 at 1:46 pm #232270
    abbots
    Participant

    Re: hoover dryer dead

    yes thanks martin,
    sorry couldn’t send reply earlier had a few problems in the office.
    thanks.
    john

    October 28, 2007 at 2:51 pm #232271
    Martin
    Participant

    Re: hoover dryer dead

    I’ve just this minute emailed them to you John….. 😉

    October 28, 2007 at 5:34 pm #232272
    abbots
    Participant

    Re: hoover dryer dead

    thanks martin,
    john

    October 29, 2007 at 11:51 am #232273
    abbots
    Participant

    Re: hoover dryer dead

    anyone got a part number for the timer on this model?
    john

    October 29, 2007 at 8:03 pm #232274
    Penguin45
    Participant

    Re: hoover dryer dead

    04750236

    Chris.

    October 29, 2007 at 9:04 pm #232275
    abbots
    Participant

    Re: hoover dryer dead

    thanks chris

  • Author
    Posts
Viewing 14 posts - 1 through 14 (of 14 total)
  • You must be logged in to reply to this topic.