Hotpoint FF200E Fridge Freezer

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Hotpoint FF200E Fridge Freezer

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • May 3, 2008 at 12:24 pm #36483
    roly16
    Participant

    The evaporator is icing up solid. The heater is ok and the thermistors appear ok; their resistance is changing with temperature anyway. Is it likely to be anything other than the main pcb at the back? The thermistors are foamed in and looking at Partfinder they don’t seem to be replacable anyway.

    Thanks

    Geoff

    May 3, 2008 at 4:29 pm #251168
    johnnyj
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    There is a mod kit available to cure new defrost heaters and cutouts and aluminuim foil to beplaced behind evaporator, before ser n/o begining 71008 use C00259476 and after 71008 use C00759745 cheers jj

    May 6, 2008 at 8:23 am #251169
    roly16
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Thanks Jonny. I went back into Partfinder armed with that info and there is a window that tells you about it.

    September 24, 2010 at 12:24 pm #251170
    Hollytree_Technical
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Can anyone send me the service bulletin (and service manual if your feeling extra generous) for these machines please – just been to see one today where there was a couple of inches of ice hanging from the evaporator – thermistors, thermal fuses and defrost heater all meter as ok.

    If not can anyone shed some light on exactly which bit has gone as I am reluctant to get a board if it isn’t that which is causing the fault.

    Thank you

    Jem

    September 24, 2010 at 4:31 pm #251171
    BobHope
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    hi Jem,

    you have email.

    Bob.

    September 24, 2010 at 5:25 pm #251172
    Hollytree_Technical
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Thank you Bob – all received. 😀

    Quick question for anyone who has done the mod – Am I right in thinking that the new heater extends lower than the old one or is that just the model in the picture?

    Thank you.

    Jem

    September 24, 2010 at 5:31 pm #251173
    BobHope
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Hi Jem,

    the new heater is larger and extend down to the fridge air return slot to stop it iceing over.

    Bob.

    September 24, 2010 at 5:43 pm #251174
    Hollytree_Technical
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Thank you Bob – looks like I will be ordering a new heater then as the customer was shocked at the size of the lump of ice that I removed this morning.

    Jem

    October 17, 2010 at 6:31 pm #251175
    A1_Domestics
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    I’ld appreciate some help with this too. Got one to look at in the morning.

    Thanks

    October 17, 2010 at 6:48 pm #251176
    BobHope
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    email sent

    Bob.

    October 24, 2010 at 10:59 am #251177
    jongriffin
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Hi
    can anyone send me the info as well please…getting quite a few of these lately
    thanks

    October 24, 2010 at 12:51 pm #251178
    Hollytree_Technical
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Check your e-mail

    Jem

    October 25, 2010 at 8:03 am #251179
    jongriffin
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Thats very useful thanks
    jon

    February 5, 2014 at 9:15 am #251180
    mic
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Hi I see this is an old thread but if anyone could send us the info it would be really helpful
    Thanks
    Wendy

    February 5, 2014 at 12:32 pm #251181
    Hollytree_Technical
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    PM me an email address and I will see what I can do.

    Jem

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 15 total)
  • You must be logged in to reply to this topic.