Bosch Classixx 1200 – Fills with water and then stops.

Home › Forums › Public Support Forums › Help And Support › Washing Machine Help Forum › Bosch Classixx 1200 – Fills with water and then stops.

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • January 11, 2009 at 2:05 pm #42483
    qprfcmark
    Participant

    Hi,

    My Bosch Classixx 1200 fills with water from the cold water feed on all cycles but then stops and does nothing further apart from the sound of a click at about 40 second intervals coming from the control switch. Drain cycle works, but spin and rinse do not.

    The details on the label inside the front loading door reads:

    E-Nr WFL2462GB/12 FD 8210 606995.

    Any ideas as to the problem?

    Thanks

    Mark.

    January 11, 2009 at 2:39 pm #273655
    Penguin45
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    Clicking will be the pcb turning the motor on and off. It’s a carbon brush motor, the carbons will almost certainly be worn out. Article HERE. Brushes to fit your motor are HERE.

    Plug and motor out to fit.

    Penguin45.

    January 11, 2009 at 2:47 pm #273656
    qprfcmark
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    Thank you Penguin45 for the quick response and links! Will let you know outcome!

    January 12, 2009 at 10:51 am #273657
    qprfcmark
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    Penguin45……….Do you have any step by step instructions / diagrams on how to remove the motor on this model? Thanks

    January 12, 2009 at 2:51 pm #273658
    qprfcmark
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    qprfcmark wrote:Penguin45……….Do you have any step by step instructions / diagrams on how to remove the motor on this model? Thanks

    Just worked it out…………..

    1: Tilt machine to access underneath of machine.
    2: Remove earth cable and live connections from motor.
    3: Stand machine upright and remove rear panel at back of machine by undoing screw at bottom of panel.
    4: Remove drive belt from motor via removed rear panel.
    5: Remove 2 retaining bolts holding motor in place via rear panel.
    6: Pull motor towards rear panel and motor will fall out of place.
    7: Remove 4 long screws holding motor together.
    8: Remove Carbon Brushes and replace.
    9: Assemble in reverse.

    Regards

    Mark

    January 13, 2009 at 12:14 am #273659
    Penguin45
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    Well done. I’m out repairing during the day, so can’t answer posts.

    Penguin45.

    June 11, 2009 at 10:29 pm #273660
    gavingolf1
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    hi,
    got the same issue on this machine.
    changed the brushes that were down to 6-8mm but still no joy.

    Hope you can help
    thks

    June 12, 2009 at 12:50 am #273661
    Penguin45
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    Test meter – circuit across the armature should read 5/6 ohms.

    Penguin45.

    June 12, 2009 at 11:05 am #273662
    gavingolf1
    Participant

    Re: Bosch Classixx 1200 – Fills with water and then stops.

    Thks for coming back.
    Armature reading was as you suggested at 5.8 ohms.

    Anything else you can suggest?
    thks
    Paul

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.