Miele Professional Dishwasher Mod. G7859

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Miele Professional Dishwasher Mod. G7859

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • October 10, 2009 at 12:17 pm #49224
    Ashby
    Participant

    Hi, Anyone familiar with this machine?
    A white film is being left on the dishes and on the inside of the machine.
    I’ve tried to reset the salt level intake as per instructions, by holding down the start and temp buttons together and switching on. The programme status “P” should appear and also the “Tap/Drain” indicator should light up. I’m getting Nothing on the display at all.
    Thanks for your help.
    Ashby

    October 11, 2009 at 6:49 am #299216
    russell555
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    make sure the dial is at the 12 o clock position when switching on…. once you get to the salt level feature set it to 19… this is the right setting unless there is a built in softener on site..then 16 is your best bet

    October 11, 2009 at 8:00 am #299217
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    Hi, Thanks for your reply. Yes, the dial was in the 12 O’Clock position,but still no joy. They have 2 machines exactly the same model and i tried this on the other machine and it worked? Any other ideas?
    Much apreciated.
    Ashby

    October 15, 2009 at 7:44 am #299218
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    Hi, Anyone have any ideas on this one please?
    Many thanks.
    Ashby

    October 19, 2009 at 3:43 pm #299219
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    No Miele experts on here?

    October 19, 2009 at 4:56 pm #299220
    russell555
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    out of curiosity ,if you were to switch off at the wall and on while holding down b and c (a=top c=bottom b=middle)does it go into programming mode??? its been known for the live on the on-off button to weld shut,causing the main control board to only switch neutral….
    what hapens if you switch on holding down a & b… if it says s21 in the display ,sounds silly but it may be easier to remove the facia panel and push the buttons without it in place,as if the contact is not great when you turn the power on it will not regester the buttons being pressed

    October 20, 2009 at 7:35 am #299221
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    Many thanks for your help, i will try that.
    Much appreciated.
    Ashby

    October 20, 2009 at 7:19 pm #299222
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    Me Again! Just had a call to say the other machine is showing a fault code F26?
    I don’t have a copy of these.
    Can someone help? Please!
    Thanks.
    Ashby

    October 20, 2009 at 8:07 pm #299223
    russell555
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    f26= flooded base… either the drain pump…or the ring holding the inlet chamber on the right hand side of the cabinet inside is loose

    October 21, 2009 at 7:48 am #299224
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    Hi Russell,
    Many thanks for your help.Again!
    Much appreciated.
    Ashby

    October 23, 2009 at 6:36 am #299225
    Ashby
    Participant

    Re: Miele Professional Dishwasher Mod. G7859

    Hi, The drain pump on this machine needs replacing.
    Where is the best place to get one please, and could you give me an idea of the cost?
    Many thanks.
    Ashby 😆

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.