Bosch (D/W) SGS43T22GB/01

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Bosch (D/W) SGS43T22GB/01

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • February 2, 2010 at 3:55 pm #52153
    rocker
    Participant

    This a currys sold dishwasher, the Enr is not reconised by bsh..its the type with the mushroom plunger….the machine fills with water runs for a very short time then aborts, water pumps then keep pumping..I have taken the cover off base, and found a small card that slots into bottom of tub with a 2 wired plug conected, I have metered this unit, reading open circuit, (is this correct) also the part number please. John.

    February 2, 2010 at 5:27 pm #310762
    nomadPaul
    Participant

    tbh John , it sounds like its leaking into the base and operating the flood protection system .

    Wasv there any traces of water once you took the metal baseplate off ? First thing i’d check is the securing nut on the salt pot where it meets the tub. Take off the salt pot lid and see if the securing nut is loose . I have had a couple where this is loose and water is leaking into the base by the salt pot lid.

    February 2, 2010 at 5:45 pm #310763
    clivejameson
    Participant

    Re: Bosch (D/W) SGS43122GB/01

    Is this one with an inline water meter (jug impellor)…i seem to recall having one where this went O/C and the machine aborted and ran the drain pump early on presumably because the pcb didn’t receive any impulses from it?

    February 2, 2010 at 5:52 pm #310764
    rocker
    Participant

    Re: Bosch (D/W) SGS43122GB/01

    Hi Gents, no sign of water in base…. No sign of impellor jug !!!

    February 2, 2010 at 7:09 pm #310765
    Washman
    Participant

    Re: Bosch (D/W) SGS43122GB/01

    Hi

    Check that model number there should be a letter between the 43 and 22


    Mike

    February 2, 2010 at 7:14 pm #310766
    rocker
    Participant

    Re: Bosch (D/W) SGS43122GB/01

    washman, you are correct the Enr SGS43T22GB/01 thanks John.
    still need help to dianose fault….please

    February 2, 2010 at 10:15 pm #310767
    clivejameson
    Participant

    Re: Bosch (D/W) SGS43122GB/01

    Ahhh this is the one with the little float magnet at about the 6 o’clock position of the sump moulding.
    Locate it, pop off its cover, remove and clean it, check for condensation in the clear half of the float (indicates it’s leaking)
    Note which way up the float fits when taking it out…IIRC the clear half is uppermost but it’s been a while since i’ve done one 😉
    HTH?

    February 2, 2010 at 10:22 pm #310768
    rocker
    Participant

    Re: Bosch (D/W) SGS43122GB/01

    Cheers Clive, have removed and cleaned the magnet, but beleive there was condensation so I will change this part, and retry. thanks John.
    PS. you dont know the part Number by any chance!!

    February 3, 2010 at 2:40 pm #310769
    rocker
    Participant

    Re: Bosch (D/W) Enr SGS43T22GB/01

    Can anyone please tell me the part number of this sliding magnet, I have rang bsh, there dont know the part I mean, also I cant see it on there drawing!!

    February 3, 2010 at 3:52 pm #310770
    Washman
    Participant

    Re: Bosch (D/W) SGS43T22GB/01

    Hi

    Part #188106 float .
    Hope that helps, it is on the drawing on Bosch Eshop page 5 for that model

    Mike

    February 3, 2010 at 4:40 pm #310771
    rocker
    Participant

    Re: Bosch (D/W) SGS43T22GB/01

    Mike. many thanks John.

    February 3, 2010 at 9:54 pm #310772
    adv
    Participant

    Re: Bosch (D/W) SGS43T22GB/01

    if float fauty or gunged up machine usualy over fills an floods kitchen. 😆

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.