Smeg dw1 710 e1 Dishwasher

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › Smeg dw1 710 e1 Dishwasher

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • April 22, 2004 at 5:32 pm #5410
    wizard
    Participant

    Can anybody help ? I’ve been to one of these today & fitted a new start cap on the circ motor. After doing what I thought was a reset I’ve ended up with the two leds on the left on together & the far right one flashing. The machine now runs constantly. Have I accidently put it in some kind if test prog ? If so how the heck do I reset it – I’ve already tried holding the prog button down, but all that does is bleeps once & goes back to two on & one flashing again. Help !

    April 22, 2004 at 7:48 pm #110962
    kwatt
    Keymaster

    Wizard,

    Just so you know that we are paying attention, I don’t have the codes to hand but I do have them in work (as will others I suspect) so if no-one answers this before then I’ll tell you in the AM.

    There was a thread on the public forums that I think Shane answered that gave the reset procedure for most of them. IIRC, it’s power off the appliance from mains and press and hold the program button within 3 seconds of reapplying power until it bleeps.

    K.

    April 22, 2004 at 8:42 pm #110963
    wizard
    Participant

    Re: Smeg dw1 710 e1 Dishwasher

    Thanks Ken, I remember seeing that one too & I tried that, but it still comes back on with the two leds on & one flashing. – Almost seems like I’ve initiated some sort of self distruct sequence ! Where’s 007 when you need him ? I’d appretiate some info if you can have a look tomorrow AM though, Thanks again.
    Wizard

    April 23, 2004 at 8:46 am #110964
    Dave_Conway
    Participant

    Re: Smeg dw1 710 e1 Dishwasher

    Wizard,

    According to Smeg’s fault code list, two lights on the left on all the time and the one on the right flashing means no heat.

    I would imagine that when the motor cap failed no water circulation has caused an overheat thermostat to trip.

    HTH

    Dave.

    April 23, 2004 at 10:10 am #110965
    wizard
    Participant

    Re: Smeg dw1 710 e1 Dishwasher

    Thanks for looking that up Dave, much appretiated. I’ll try that, but it only started doing it after I tried to cancel the program initially, machine had only been running for 2 mins. I’ll let you know later what occurs. Ta

    Wizard

    April 23, 2004 at 5:21 pm #110966
    wizard
    Participant

    Re: Smeg dw1 710 e1 Dishwasher

    Sorted !! safety stat was OC. Shorted that out & still wouldn’t cancel, so removed the outer door & shorted the cycling stat aswell. Machine made a load of beeps, pumped out & reset !!! So all I’ve got to do now is order a new safety stat. Phew!! What a git ! Thanks for your help lads.
    Wizard

    April 23, 2004 at 6:16 pm #110967
    Dave_Conway
    Participant

    Re: Smeg dw1 710 e1 Dishwasher

    Not a git, a magician 😀

    Now can you make my credit card bill disappear please 😆

    Glad you got it sorted.

    Dave.

  • Author
    Posts
Viewing 7 posts - 1 through 7 (of 7 total)
  • You must be logged in to reply to this topic.