ZAN ZJD12191 Fills then stops

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › ZAN ZJD12191 Fills then stops

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • October 8, 2010 at 1:51 pm #57819
    pmb
    Participant

    ZJD 12191. 91460121801
    If i put on wash it fills then after a couple of minutes it stops and start/pause
    flashes,
    I have checked heater, its ok. Spins OK
    I know i should do diagnostics check but i dont have it for this model.
    😕

    October 8, 2010 at 4:03 pm #332403
    Martin
    Participant

    Re: ZAN ZJD12191 Fills then stops

    pmb wrote:I know i should do diagnostics check but i dont have it for this model.

    Well if you hold a Connect a/c you can at least download it from their Mediator options if you wish.:wink:

    October 9, 2010 at 1:03 pm #332404
    Bernie
    Participant

    Re: ZAN ZJD12191 Fills then stops

    Check you email

    October 10, 2010 at 8:36 pm #332405
    leavemetogetonwithit
    Participant

    Re: ZAN ZJD12191 Fills then stops

    pmb wrote:
    I have checked heater, its ok

    If it’s a washer/drier pay special attention to page 86.
    Mike.

    October 11, 2010 at 7:28 am #332406
    pmb
    Participant

    Re: ZAN ZJD12191 Fills then stops

    The pages only go up to 67. ❓

    October 11, 2010 at 7:37 am #332407
    Martin
    Participant

    Re: ZAN ZJD12191 Fills then stops

    leavemetogetonwithit wrote:If it’s a washer/drier pay special attention to page 86.

    Mike refers to the old 118 page ‘general’ manual and not the 67 page EWM2000 series ‘test’ manual. In that one no doubt Mike would wish you to note the contents of page 49.:wink: 🙂

    October 11, 2010 at 5:49 pm #332408
    pmb
    Participant

    Re: ZAN ZJD12191 Fills then stops

    Couldnt find it on connect,
    Forgot i had it on TDS Disc.
    Also Bernie Emailed it to me,Thanks,
    Did the Diagnostic,”E36″ Seems to be PCB, Told them to ring Zanussi

    October 11, 2010 at 6:35 pm #332409
    Seamy
    Participant

    Re: ZAN ZJD12191 Fills then stops

    E36 is not always the board, it most likely will be the DRYER HEATER 1242658308 ,, disconnect all dryer heater cables & tape up securely. Try on wash cycle, you’ll more than likely find theres no E36 then. 💡

    October 11, 2010 at 6:37 pm #332410
    garn
    Participant

    Re: ZAN ZJD12191 Fills then stops

    Had A Couple of These Over The year Same Fault everything Working Separately.

    The Sump Iv Found A Thin Layer of Washscumgrease Lining The Sump Filter
    Pulled It Of Throughly Cleaned It And Blew Air into The Pressure Switch And Its Up And Running.

    October 11, 2010 at 7:33 pm #332411
    leavemetogetonwithit
    Participant

    Re: ZAN ZJD12191 Fills then stops

    Martin wrote:

    leavemetogetonwithit wrote:
    If it’s a washer/drier pay special attention to page 86.

    Mike refers to the old 118 page ‘general’ manual and not the 67 page EWM2000 series ‘test’ manual. In that one no doubt Mike would wish you to note the contents of page 49.:wink: 🙂
    Indeed.
    I can’t find a 67 page one 😕
    I just had got fed up repeating “40 Megohms” all the flippin’ time 😆 .
    Mike.

    October 12, 2010 at 7:31 am #332412
    Martin
    Participant

    Re: ZAN ZJD12191 Fills then stops

    leavemetogetonwithit wrote:I can’t find a 67 page one 😕

    I’ll send you a copy Mike…check your email!:D

    October 12, 2010 at 9:55 pm #332413
    leavemetogetonwithit
    Participant

    Re: ZAN ZJD12191 Fills then stops

    Thankyou for that, Martin. My education is proceeding apace.

    A snail’s pace.

    No, no I didn’t mean that last bit. Just joking. 😆
    Mike.

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.