PCB for a Candy CM1166-80

Home › Forums › Public Support Forums › Help And Support › Washing Machine Help Forum › PCB for a Candy CM1166-80

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • June 1, 2011 at 5:02 pm #63126
    Enfys
    Participant

    Hi

    I can see a Module for sale on the shop for Module No 41013731 and I have a Faulty 41013727

    Will the one for sale work as a Replacement.

    Thanks

    June 1, 2011 at 7:31 pm #352670
    helo_75
    Participant

    Re: PCB for a Candy CM1166-80

    neither of thise numbers are correct for your machine

    the correct number you need is

    09200779

    do you have the first 8 digits of ur serial number to make 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure

    June 1, 2011 at 7:32 pm #352671
    helo_75
    Participant

    Re: PCB for a Candy CM1166-80

    and why do u think the module is faulty?

    June 2, 2011 at 8:19 am #352672
    Enfys
    Participant

    Re: PCB for a Candy CM1166-80

    Hi
    The Module Number I gave is actually on the board, so that appears to be the correct module. I’m not at the office right now for the Serial Number, but will get back. The Machine is intermittently cutting out. I suspect the board because other parts seem to work ok and the Board has lost its proper mounting to the machine. i.e. the Plastic Backboard has snapped and its not held in its proper place.

    June 2, 2011 at 4:52 pm #352673
    helo_75
    Participant

    Re: PCB for a Candy CM1166-80

    the only reason i ask, is cos that number u have technically doesnt exist, it must have been superseeded, ifu can get the serial number, i will confirm the exact one u need!

    June 2, 2011 at 6:19 pm #352674
    Enfys
    Participant

    Re: PCB for a Candy CM1166-80

    I’ve attached an Image, and you can see its on the Label, but perhaps as I’ve reduced it due to limitations here, you might not see well.

    June 2, 2011 at 7:22 pm #352675
    kwatt
    Keymaster

    Re: PCB for a Candy CM1166-80

    That’s the input module you’re looking at in the store. It does little apart from tell the Coreboard what to do as it’s the one behind the buttons on the facia. I would very much doubt that was the cause of intermittent cutting out, in fact I’d say it was a 95{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} or higher chance that it isn’t.

    If it’s the Coreboard, which is what that looks like, you need the version programmed specifically for the model, the numbers on the board could be any sort of factory reference that likely means little outside the factory as it usually doesn’t.

    The programmed board is part number 09200779 and is a special order for just about everyone. They’re about £70 a pop plus VAT and shipping so it’s an expensive part to take a punt on.

    HTH

    K.

    June 3, 2011 at 8:29 am #352676
    Enfys
    Participant

    Re: PCB for a Candy CM1166-80

    Ok, thanks. I’ll see if I’ve got another coreboard with one of the other machines I’ve got lying around, if not, I may just sell another working one, which has got to be better for the Customer. Appreciated your input

    June 3, 2011 at 10:52 am #352677
    Enfys
    Participant

    Re: PCB for a Candy CM1166-80

    Looks like I can get it repaired on a same Day Service now for around £40 inc vat. I’m going to give that consideration.

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.