Beko wm5120s

Home › Forums › Public Support Forums › Help And Support › Washing Machine Help Forum › Beko wm5120s

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • June 3, 2011 at 9:58 pm #63168
    elfy1960
    Participant

    Hi my washer is playing up when you turn it on the ready light should come on but instead the wash light comes on,it will then either fill up and do nothing else or it wont fill up at all, if you pause it and select drain to empty sometimes it will and other times not.I have had the motor out and checked the brushes and they are fine whenput the motor back on and tried it it worked ok but today its acting up again, any pointers to what i should do please . Elfy

    June 3, 2011 at 11:41 pm #352827
    kwatt
    Keymaster

    Re: Beko wm5120s

    It may be a board fault depending on the number of LEDs that machine has on it. Does the light flash or is it constant?

    K.

    June 4, 2011 at 9:32 pm #352828
    elfy1960
    Participant

    Re: Beko wm5120s

    The wash light is constant and when pressed it flashes in pause mode but the ready light should be on. Tried it again today and it filled up then thats it nothing else happens,flicked it over to empty and still nothing .

    June 4, 2011 at 11:11 pm #352829
    kwatt
    Keymaster

    Re: Beko wm5120s

    I think, from what I can see, that the machine is telling you that the heater is open circuit, easily tested with a meter.

    K.

    June 5, 2011 at 12:04 am #352830
    elfy1960
    Participant

    Re: Beko wm5120s

    Cheers for that info but now what do i do , i have a multi meter . does it mean a new heater or is it faulty wiring

    June 5, 2011 at 10:07 am #352831
    kwatt
    Keymaster

    Re: Beko wm5120s

    You need to test it as I said.

    K.

    June 9, 2011 at 8:27 pm #352832
    elfy1960
    Participant

    Re: Beko wm5120s

    Hi ive tested the heater for continuity and my meter bleeped so thats saying the heater is ok but am still not getting it to work. All it does now when you switch it on is run the pump for a few seconds then zilch . Is there any other test i can do on the heater as i have seen another post about a beko and they too were told to check the heater, cheers Elfy

    June 9, 2011 at 8:52 pm #352833
    johnsdad
    Participant

    Re: Beko wm5120s

    Check the motor brushes, it won’t start a prog if they are worn out

    June 9, 2011 at 9:28 pm #352834
    elfy1960
    Participant

    Re: Beko wm5120s

    Have already checked the brushes they are fine

    June 10, 2011 at 7:47 am #352835
    washtronics
    Participant

    Re: Beko wm5120s

    hold start button in until end light comes on, wait for door to unlock then you can start programme again

    June 10, 2011 at 6:52 pm #352836
    elfy1960
    Participant

    Re: Beko wm5120s

    The end light is already on when the washer is turned on. Is there any other test i can do on the heater, don,t want to buy a new one and find out its something else

    June 24, 2011 at 6:56 am #352837
    BEKOBOY
    Participant

    Re: Beko wm5120s

    Check the drain pump impellor, as if it gets obstructed, it will give the electronics o the unit to play up and lock programmes. Quyite a common fault with this model.

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.