Indesit DV620whuk pcb inisialize

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › Indesit DV620whuk pcb inisialize

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • December 7, 2011 at 9:48 am #66719
    royston h
    Participant

    I recently fitted a new timer card and it did not inisialise properly on my indesit dv620 all i have onnow is the red power light and when i make a setting it just beeps how do i reset and get it inisalised properly.
    Many thanks

    December 7, 2011 at 10:46 am #364998
    iadom
    Moderator

    Re: Indesit DV620whuk pcb inisialize

    What was the reason for changing the PCB?

    There are at least two different PCB’s for this machine, have you got the correct one?

    Have you still got the old PCB?

    Full serial number & commercial code needed to verify correct part number.

    December 7, 2011 at 12:34 pm #364999
    royston h
    Participant

    Re: Indesit DV620whuk pcb inisialize

    The water would not get hot everything else worked fine the new board is a C00143206 and it has a buzzer the old one which i still have has 21010324502 S1 ID:4014622 on it and had no buzzer.

    December 7, 2011 at 2:49 pm #365000
    iadom
    Moderator

    Re: Indesit DV620whuk pcb inisialize

    If your appliance serial number is 40505.0000 or less then that is the correct part.
    If the serial number is 40505.0001 or higher then you have the wrong PCB.

    Did you test the heating element first? The solid bar type element inside the tub that yours has is far more reliable than the internal tube type but should still be tested first.

    If there is a pre existing fault on the machine the PCB will not initialise, sometimes replacing the old PC running it to see if you get an error code and then refitting the new one can work.

    December 8, 2011 at 9:57 am #365001
    royston h
    Participant

    Re: Indesit DV620whuk pcb inisialize

    Thanks for the reply i did check the heater element and it was fine i will try what you suggested not sure on the serial number as its fitted in machine at the minute i will check that next and fit the old board again, i will report back and thanks again

    December 8, 2011 at 10:28 am #365002
    royston h
    Participant

    Re: Indesit DV620whuk pcb inisialize

    Just put the old board back in and it worked straight away but the water temp did not rise, the numbers on the new board are 21500933903 ID:1013721 is this correct?

    December 8, 2011 at 10:35 am #365003
    iadom
    Moderator

    Re: Indesit DV620whuk pcb inisialize

    iadom wrote:If your appliance serial number is 40505.0000 or less then that is the correct part.
    If the serial number is 40505.0001 or higher then you have the wrong PCB.


    Was this not clear? 😉 😀

    Look on the rating plate, usually down the side of the door.

    December 8, 2011 at 10:40 am #365004
    royston h
    Participant

    Re: Indesit DV620whuk pcb inisialize

    50207 3058 thanks sorry must learn to read properly

    December 8, 2011 at 10:46 am #365005
    iadom
    Moderator

    Re: Indesit DV620whuk pcb inisialize

    You have been supplied with the wrong PCB, you need
    C00109875.

    December 14, 2011 at 12:31 pm #365006
    royston h
    Participant

    Re: Indesit DV620whuk pcb inisialize

    Sent the other board back explained the problem and the board that i needed and i have been sent through a C00143211 VERSION S1 is this one ok before i unpack it all ?
    thanks

    December 14, 2011 at 12:44 pm #365007
    Martin
    Participant

    Re: Indesit DV620whuk pcb inisialize

    royston h wrote:i have been sent through a C00143211 VERSION S1 is this one ok before i unpack it all ?
    thanks


    Yes! Yes! that is the latest replacement up-dated part number for the number Iadom gave you(C00109875)so it will be fine!

    😀

    December 14, 2011 at 12:49 pm #365008
    royston h
    Participant

    Re: Indesit DV620whuk pcb inisialize

    Thank you very much 🙂

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • You must be logged in to reply to this topic.