Bosch Classixx SGS45C02GB/11

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › Bosch Classixx SGS45C02GB/11

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • December 31, 2013 at 4:51 pm #78797
    TlbSilver
    Participant

    Hello

    I have had this dishwasher some time and it has recently started to take longer and longer to complete a full cycle on any wash program. Today the ‘check water’ light came on and the machine is stuck on a cycle with 20 minutes displayed on the timer.

    It appears to be filling through the side inlet at the bottom until it is almost leaking from the door and then the pumps kicks in to drain it. I let it repeat this cycle for a further 25 minutes and then switched it off.

    I have read in another thread/post that it could be the impeller jug, is this a good starting point or are there other possibilities or checks I can make first?

    Thank you for any help.

    Silver.

    December 31, 2013 at 5:14 pm #406949
    stevebunyan
    Participant

    Re: Bosch Classixx SGS45C02GB/11

    Hi
    The Fill Metering Device/Jug does sound to the most likely conclusion. Try unplugging the connector to it and plugging it in again to make a better connection first. Dont forget to unplug the appliance from the mains before you work on it.

    December 31, 2013 at 5:23 pm #406950
    TlbSilver
    Participant

    Re: Bosch Classixx SGS45C02GB/11

    stevebunyan wrote:Hi
    The Fill Metering Device/Jug does sound to the most likely conclusion. Try unplugging the connector to it and plugging it in again to make a better connection first. Dont forget to unplug the appliance from the mains before you work on it.

    Thanks, I’ll give it a try tomorrow.

    January 1, 2014 at 3:15 pm #406951
    TlbSilver
    Participant

    Re: Bosch Classixx SGS45C02GB/11

    I’ve had a chance to look at the dishwasher today and have checked the connection on the metering device. It all looks normal, the device is spinning freely with little noise or vibration. Is there an electrical check that can be performed on this part to check its functioning properly.

    Thanks.

    January 1, 2014 at 4:01 pm #406952
    Martin
    Participant

    Re: Bosch Classixx SGS45C02GB/11

    No point in messing with the impellor jug as they wear very quickly. Replace it, job done!

    January 1, 2014 at 8:38 pm #406953
    TlbSilver
    Participant

    Re: Bosch Classixx SGS45C02GB/11

    Martin wrote:No point in messing with the impellor jug as they wear very quickly. Replace it, job done!

    Thanks for the reply. I’ve ordered a new one and will report back once it’s fitted.

    January 7, 2014 at 7:07 pm #406954
    TlbSilver
    Participant

    Re: Bosch Classixx SGS45C02GB/11

    Changed the Impellor jug and it’s 28 minutes into a 30 minute program. It all seems to be working as it should and the elapsed time matches the program time. For any other amateurs or novices, It’s a simple job to change on these machines and I think all you could possibly do wrong it put it in the wrong way around. It has a very small arrow on the plastic and I just replaced with this pointing the same direction. I don’t know, but assumed the arrow was direction of flow.


    Thanks for the help. 😀

  • Author
    Posts
Viewing 7 posts - 1 through 7 (of 7 total)
  • You must be logged in to reply to this topic.