Baumatic BDI631 Thermostat

Home › Forums › Public Support Forums › Help And Support › Dishwasher Help Forum › Baumatic BDI631 Thermostat

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • November 18, 2015 at 7:56 pm #86733
    rothie
    Participant

    Hi

    Could anyone tell me where the thermostat is on this machine. I have looked at the replacement ones on sites but cant see anything like this under the machine.

    Thanks

    November 18, 2015 at 8:19 pm #432885
    admin
    Keymaster

    Re: Baumatic BDI631 Thermostat

    Hi

    It’s in the base BUT what is the actual fault you have ?

    Bryan

    November 18, 2015 at 8:36 pm #432886
    rothie
    Participant

    Re: Baumatic BDI631 Thermostat

    Hi
    The fault is the dishwasher is not heating the water, I have tested the heater and it is ok, so was looking for the thermostat.

    Thanks
    Graeme

    November 18, 2015 at 8:41 pm #432887
    admin
    Keymaster

    Re: Baumatic BDI631 Thermostat

    Hi

    Put it on a wash then after it has filled with water pour another 3/4 ltr into it and then close the door and see if it heats up then.

    Bryan

    November 18, 2015 at 10:50 pm #432888
    rothie
    Participant

    Re: Baumatic BDI631 Thermostat

    Hi
    Thanks for that Bryan, tried it but no change. sorry for the late reply I couldn’t access the site.

    Graeme

    November 18, 2015 at 11:57 pm #432889
    admin
    Keymaster

    Re: Baumatic BDI631 Thermostat

    Hi.
    Then it will be the one shot stat in the base. If you look at the back whilst it is washing the water should be pumped up the rear tube. If it’s not then it may be the diverted flap on the side of the motor which can be removed if you don’t want or use the 1/2 load option.
    You won’t easily see the button stat if you don’t remove the rear panel and base panel..

    But remember… Unplug it !!

    Bryan

    November 19, 2015 at 10:51 am #432890
    rothie
    Participant

    Re: Baumatic BDI631 Thermostat

    Hi Bryan
    Thanks for that
    I Have removed the base again but still can’t see anything that looks like the ones offered for sale. There is a small bullet shaped sensor on the outlet held in by 2 small screws.

    Graeme

    November 19, 2015 at 8:17 pm #432891
    rothie
    Participant

    Re: Baumatic BDI631 Thermostat

    Hi
    Could this be a temp transmitter / thermistor?

    Thanks

    November 19, 2015 at 8:25 pm #432892
    admin
    Keymaster

    Re: Baumatic BDI631 Thermostat

    Hi

    I’m not in front of it so can’t see what you see. The cut out is normally screwed into the base or on the back cross member. also if there is not enough pressure going through the pipework from the motor through a black rubber hose with a microswitch attached then goes unto the top spray arm..

    Bryan

    November 19, 2015 at 9:15 pm #432893
    rothie
    Participant

    Re: Baumatic BDI631 Thermostat

    Hi Bryan

    I have attached a pic of the probe, have you any idea if this could be it?

    Thanks
    Graeme

    April 3, 2016 at 11:19 am #432894
    bullettooth_toby
    Participant

    Re: Baumatic BDI631 Thermostat

    Hi Graeme,

    Did you ever get this resolved as I have the exact same problem?

    I purchased the official replacement before even opening the machine as I was confident it was a thermostat issue. However, the part that I bought looks is the blue one in the picture, but like you, the only thing I can find that looks like it could be the thermostat is the other one which is identical to what you pictured.

    Can you help me out at all with how you got this sorted?

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)
  • You must be logged in to reply to this topic.