bosch dishwasher e09

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › bosch dishwasher e09

Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • March 7, 2017 at 6:26 pm #90762
    HotDog
    Participant

    I have not been to this yet i know it could be the heat pump what sort of job are they to fit as i have not done one yet ,customer says it does get slightly warm so not sure any one advise

    March 7, 2017 at 8:31 pm #445889
    codlets
    Participant

    Re: bosch dishwasher e09

    I Can’t say i’ve ever had one where it only gets warm, but what I would do first is check the PCB for dry solder joints on the heater relay as this is a common problem

    March 7, 2017 at 9:53 pm #445890
    HotDog
    Participant

    Re: bosch dishwasher e09

    thanks for that will check joints i thought it was odd that they say it gets warm

    March 8, 2017 at 6:55 am #445891
    timdowning
    Participant

    Re: bosch dishwasher e09

    Its probably a bit warm because it has been circulating the water for or a while or it may be connected to the hot supply.
    I would check the heater first as taking the module out to check is a lot more fiddly…

    March 8, 2017 at 8:38 pm #445892
    HotDog
    Participant

    Re: bosch dishwasher e09

    you are right after further phone call we have found it is connected to the hot water supply so i will be checking heat pump still would like to know what its like to fit one

    March 8, 2017 at 8:58 pm #445893
    timdowning
    Participant

    Re: bosch dishwasher e09

    I’ve posted quite a few times on heat pump replacement.
    Nice & simple can all be done through the front access panel.

    March 8, 2017 at 10:23 pm #445894
    nomadPaul
    Participant

    Re: bosch dishwasher e09

    timdowning wrote:I’ve posted quite a few times on heat pump replacement.
    Nice & simple can all be done through the front access panel.

    I’ve done *cough cough* a fair few but never through the front. Personally takes me 10/15 mins from the side although I know some of the lads can do them through the front. Do you leave the original hose clip in position or fit the new jubilee clip ?

    March 9, 2017 at 6:55 am #445895
    timdowning
    Participant

    Re: bosch dishwasher e09

    I always use the new jubilee clip!!

    I always did the freestanding with the side off then I thought that as I do the integrated ones through the front why not that way on freestanding.
    You disturb no connections / plumbing plus you can do a visual afterwards with the front panel still off.

    March 9, 2017 at 3:28 pm #445896
    eastlmark
    Moderator

    Re: bosch dishwasher e09

    timdowning wrote:I always use the new jubilee clip!!

    I always did the freestanding with the side off then I thought that as I do the integrated ones through the front why not that way on freestanding.
    You disturb no connections / plumbing plus you can do a visual afterwards with the front panel still off.

    can you access the clip to tighten it from the front?

    March 9, 2017 at 3:33 pm #445897
    timdowning
    Participant

    Re: bosch dishwasher e09

    Yes

  • Author
    Posts
Viewing 10 posts - 1 through 10 (of 10 total)
  • You must be logged in to reply to this topic.