no fill hpt bf72

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › no fill hpt bf72

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • April 30, 2005 at 9:29 am #9298
    streetlighter
    Participant

    Hi all
    Can any one help with this problem
    Hpt integral d/w bf72. she fires up the display but when you shut the door you get 2 beeps ( appantly normal ? ) then silence.
    checked drain pump as it should come on first but it seems ok, when you lift the flood protection float it fires up, but the supply to it is only 99v not 240v at the start of the program.
    I am not sure if I have a modual problem feeding the pump or a fill / blockage problem.
    Tested neutral all round and seemded ok, but I couldnt get the d/w out ( customer to dismantle kitchin today so I can ).
    I had no fault code showing at all.
    Does any one have the circuit dia or the ins on how to run test seq on this.
    Already spent 2 1/2 hrs on it last night so any help would be apreciated.
    Thanks.

    Paul

    April 30, 2005 at 9:47 am #133393
    eastlmark
    Moderator

    Re: no fill hpt bf72

    This is a smeg made one so check the coil on the dispenser and also the inlet valve. Have you left it long enough after the beeps? Sometimes they sit there is silence for a good minute or so before doing much. unusual not to get an error code though so may be a module problem.

    April 30, 2005 at 9:59 am #133394
    streetlighter
    Participant

    Re: no fill hpt bf72

    Hi all
    Sorry Forgot to say made in italy on the lable does this change things ?

    Paul

    April 30, 2005 at 10:42 am #133395
    Dave_Conway
    Participant

    Re: no fill hpt bf72

    Nope, it’s still a Smeg 😉

    Check all the usuals as per any other Smeg unit (Diplomat etc), they’re all pretty much the same Paul.

    Dave.

    May 1, 2005 at 9:03 am #133396
    jimbo2207
    Participant

    Re: no fill hpt bf72

    with the door open, switch the appliance on and within 2 seconds press the prog select button 4 times rapidly. The display will go to F! which indicates that it’s now in test mode. Pressing the half load button allows you to step through the test progs

    I’ve got the full diagnostic paperwork, but it goes on for weeks.

    May 1, 2005 at 7:57 pm #133397
    streetlighter
    Participant

    Re: no fill hpt bf72

    Hi all
    Thanks for you advise i’ll be poping back tuesday hopefully he would have got it out by then.
    Does anyone have a wiring diagram for this

    paul

    May 2, 2005 at 6:54 pm #133398
    eastlmark
    Moderator

    Re: no fill hpt bf72

    most of what you need to check can bevdone with the machine in situ.

    May 6, 2005 at 10:40 am #133399
    streetlighter
    Participant

    Re: no fill hpt bf72

    Hi all
    Should I laugh or cry ❓
    Checked all the usual things to no avail, so thought I go for it and try the test sequence not even knowing what any of it ment.
    Went through no problems fill pump dispensor wash pump lots of c8,s and c6,s ete all ok ❓
    When started up all was ok now, pump fill wash dispensor heater ete ❓
    God knows what did it but it now seems ok.
    Do you think the test sequence reset the modual or just freed something up, I never did find out what the problem was. 😕

    Paul

    May 22, 2005 at 5:37 pm #133400
    streetlighter
    Participant

    Re: no fill hpt bf72

    Thanks again for your help on this one guys/girls.
    Just bin back to do a neff fan ele change and the dishwasher is A OK 🙂
    Should have charged her more.

    Paul

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.