Hotpoint SDL510 Stopped Pumping

Home Forums Public Support Forums Help And Support Dishwasher Help Forum Hotpoint SDL510 Stopped Pumping

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • #98184
    Ash Kiwano
    Participant

    Hi! Looking for help with my Hotpoint SDL510 Dishwasher , it has started to flash these two lights and won’t drain the water, I usually hear a pump but nothing, I read online it may be a blocked waste pipe but I have used a wet and dry vacuum on it and there are no obstructions so I am now confused?

    https://ibb.co/xY0CqCb

    Thanks!
    Ash

    #471270
    electrofix
    Moderator

    could still be blocked
    if its jammed completly it will just be a faint hum which can be difficult to hear

    Dave

    #471271
    Ash Kiwano
    Participant

    Hi Dave

    I’ve put the wet and dry hoover on the end of the pipe and can feel the suction from the bottom of the drain inside the machine so it can’t be blocked still.

    I know the hum that you’re talking about which it usually makes when it’s draining but it’s completely silent now

    #471272
    electrofix
    Moderator

    no you dont get it
    if the impellor is jammed and cant move it will make a very quiet hum but you have to listen very hard to hear it

    Dave

    #471273
    Ash Kiwano
    Participant

    Okay I’ll pull the machine back out, will the sound come from the back of the machine? Thanks

    #471274
    electrofix
    Moderator

    the sound will come from the pump and probably very faint

    you can see the grey outlet hose coming off the pump

    Dave

    #471275
    Ash Kiwano
    Participant

    Hi! So I have the panel off and I can hear a very faint noise it sounds like a high pitch noise ?

    #471276
    Ash Kiwano
    Participant

    Here’s a photo of the underneath

    https://ibb.co/XJXhJtJ

    #471277
    electrofix
    Moderator

    remove the pump and see if its jammed

    there are normally plastic clips to lock it on

    Dave

    #471278
    Ash Kiwano
    Participant

    Is that the white thing on the right in my photo?

    #471279
    electrofix
    Moderator

    correct
    photo a bit blurred but you can see the lock and pump twists and unlocks

    Dave

    #471280
    Ash Kiwano
    Participant

    Hi!

    so I took the panel off today and removed the motor and i couldn’t see anything wrong with it?

    here is a video

    https://streamable.com/gynlyj

    Put it all back and started a cycle and again, would not empty, any suggestions now?

    Ash

    #471281
    electrofix
    Moderator

    no that looks good

    well next thing i would have done is checked the pump windings

    if ok i would then trace the pump wires back to the board and check continuity

    then look where the pump connects to the board and trace the connections to the triac that controls the pump and look for circuit damage

    Dave

    #471282
    Ash Kiwano
    Participant

    Hi Dave

    I just want to say thank you for all your help, I’m not an electrician so I have no idea about checking circuit boards etc, I was just trying to save this from
    being scrapped and calling someone out is going to be just as expensive as a new dishwasher.

    Thank you again
    Ash

    #471283
    electrofix
    Moderator

    no problem

    i was hoping it was glass in the pump as it normally is but you get the challenging one

    Dave

Viewing 15 posts - 1 through 15 (of 15 total)
  • You must be logged in to reply to this topic.