Amica AWCT Fault Codes
Fault codes for the Amica AWCT range of washing machines that display a fault using a series of lights or LEDs to indicate the fault that has been detected on the washing machine.
The error code is displayed as the relevant lights being lit on the washing machine control panel although the position or function of each LED may differ from model to model.
A sample of the order is shown in the image to the right.
Before you start any investigation of the fault or even remove the lid of your Amica washing machine please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!
Please remember to support our site by buying Amica washing machine spares from our store and, if you decide that you need an engineer please support the local repairers that help make this site possible, you can search for a repairer using the engineer search facility.
Amica Washing Machine Fault Codes
These fault codes are written for washing machine repairers and not for the general public by Amica and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault guide from this link before you begin.
Please check that any Amica washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine or washer dryer. Please, don’t guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.
If you struggle or cannot find the appropriate fault code that you need for your Amica machine please ask in the forums and the gusy there will do what they can to help and locate the meaning of the fault code you need
Fault Code Lights Legend
This is our very simple legend to show the state of the lights, lamps or LED’s as they are unlit, flashing or lit continuously.
 |
Light or LED not lit |  |
Light or LED flashing |  |
Light or LED lit solid, no flash |
Amica Washing Machine Fault Codes For AWCT Range
|
|
|
|
|
No door lock signal detected / No door lock triac signal / Door not unlocked in two minutesThis fault code can correspond to any of the three faults listed above.
|
|
|
|
|
|
Fill time has exceeded two minutes / No signal from pressure switch after ten minutesThis fault code can correspond to either of the two faults listed above.
|
|
|
|
|
|
Water not drained from washing machine in allotted timeThe level sensor has not detected that the washing machine has been drained inside one and a half minutes or, the machine has not been detected as empty after ten minutes from start of drain.
|
|
|
|
|
|
Overflow – overfilling with waterWater level has exceeded the overfill level on the pressure switch or sensor
|
|
|
|
|
|
Heater or NTC error detected
|
|
|
|
|
|
Washing machine motor does not work
|
|
|
|
|
|
Input voltage incorrectThe power supply voltage is outside of 160-235 Volts, 50/60Hz
|
More Amica Washing Machine Help
Should you need more help and guidance please use the links from this article as most of them will help you to understand your Amica washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.
In addition you can post in our help and advice forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
- We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
- We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
- We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
- No warranty is inferred, implied or given.
Also note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Amica washing machine model please post a request to confirm this in the forums.
Model number AWCT10L. I am have trouble in that when the machine finishes washing cycle and goes to rinse it stops working. As you look at the machine its the 2nd light from the right lights up red all the others go green. Can you please advise…..
Hello,
I can see your comment from a while ago. I have a exact same problem. As it just stops working mid wash then second light from right goes red other two to three left go orange. Did you figure out what was the issue? Please help thank you ?
I have a new Amica washing Machine, It worked the 1st time ok., Now when I press start or even just plug it in the END sign lights up, and then nothing happens, it just won\’t start.
I am trying to put a wash on but when I go to change the temperature it keeps going back to 60 degrees and is flashing on this temperature. Please advise.
My Amica Navigator System AWB12L start/pause button is Red then after 30 seconds start flashing. There are no noises of water draining or pump